Caleido SP1CR Technical Manual - Page 4

Browse online or download pdf Technical Manual for Heater Caleido SP1CR. Caleido SP1CR 6 pages.

Print Page

INSTALLATION INSTRUCTIONS

1. The device must not be placed in front of a power socket.
2. Prevent the device from being hit by water jets.
3. When installed in rooms with a bath or shower, observe the "protection zones" for insulation class IP 44 (in the UK according to IEE wiring
regulations).
Also, observe all local regulations.
4. When connecting the electrical wiring, the brown wire is live (L), the blue wire is neutral (N) and the yellow/green wire must be connected to earth.
5. It must be protected with a 30mA residual current device (RCD).
6. Ensure that the mains voltage is the same as indicated in the technical specifications.
USER MANUAL
1. The device must not be placed in front of a power socket.
2. Prevent the device from being hit by water jets.
3. When installed in rooms with a bath or shower, observe the "protection zones" for insulation class IP 44 (in the UK according to IEE wiring
regulations).
Also, observe all local regulations.
4. When connecting the electrical wiring, the brown wire is live (L), the blue wire is neutral (N) and the yellow/green wire must be connected to earth.
5. It must be protected with a 30mA residual current device (RCD).
6. Ensure that the mains voltage is the same as indicated in the technical specifications.
IR receiver
"Mode" LED: red / green / amber.
A small warning light tells the user
which functions are active.
USER GUIDE
On/stand-by
Press the (On/Stand-by) button on the remote control or thermostat to switch on or activate the "Stand-by" mode.
When the device is switched on, it emits a 0.5-second sound; when "Stand-by" mode is activated, it emits two 0.5-second sounds.
Switching on directly from the thermostat attached to the towel warmer activates "Comfort" mode with a set temperature of 20°C. The remote control
must be used to change the temperature or activate other functions.
Comfort mode
"Comfort" mode maintains the room temperature at the value set by the user. Press the (mode) button
until the "Comfort" icon appears on the display.
Use the (+) and (-) buttons to set the desired temperature. In "Comfort" mode, the mode LED is red.
Night mode
In "Night" mode, a lower temperature value than "Comfort" mode is set. This mode is activated by pressing the (mode) button
until the desired icon appears.
Set the desired temperature with the (+) and (-) buttons. In "Night" mode, the Mode LED is green.
Antifreeze mode
In "Antifreeze" mode the heating element switches on when the room temperature falls below 7°C. This mode is
activated by pressing the (mode) button until the desired mode icon appears.
In "Antifreeze" mode, the Mode LED is flashing green.
2H Boost mode
The heating element switches on to reach a room temperature of 32°C and stops automatically after 2 hours. This mode is activated by pressing the button
(2h Boost); the "2h" icon appears on the display.
To exit this mode, press the 2h Boost button, the On/Stand-by button or the mode button. In 2h Boost mode, the Mode
LED is flashing red.
Chrono mode:
This mode allows you to set a daily programme repeated on a weekly basis. This mode is
activated by pressing the mode button until the "Chrono" icon appears.
In "Chrono" mode, the On/Standby LED is amber.
The Mode LED is green during the "Night" period and red during the "Comfort" period.
4
• Disconnect the appliance from the mains before installation or maintenance.
• Protect the device with a 30mA residual current device (RCD).
User manual
"On/Stand-by" LED:
the LED indicates the
status of the
thermostat.
Button [On/stand-by].
Low battery
Energy consumption
Operating mode symbol:
Fil-Pilot
Comfort
Night
Anti-frost
Boost 2h
ECO
Clock
Daily programme in "Chrono" mode
Heating element.
Button [chrono]
1/2" GAS
thread for
attachment
Button [-]
to the towel
warmer.
NTC probe
Button [Boost 2h]
Power cord.
Remote control signal transmission symbol
Set temperature
"ECO" mode symbol
"Key lock" symbol
Backlit display
Button [Mode]
Button [+]
Button [On/stand-by]
Button [ECO/Window open sensor]
CHRONO
ASC
Day of the week