Xerox ColorQube 9201 Secure Installation And Operation - Page 9
Browse online or download pdf Secure Installation And Operation for All in One Printer Xerox ColorQube 9201. Xerox ColorQube 9201 12 pages. Mfp
Also for Xerox ColorQube 9201: Install And Operation Instructions (14 pages), Evaluator Manual (28 pages), Quick User Manual (38 pages), Quick Manual (8 pages), Quick Manual (16 pages), Secure Installation And Operation (12 pages), How To Make A Copy (9 pages)
Print Page
15. Users should be aware that correct remote repository document pathnames for the receipt of workflow scanning jobs should
start with one '\' as opposed to the two '\'s shown in the SAG (e.g., page 10-15).
16. Xerox recommends that users undergo appropriate training on how to use the device in a secure manner before being assigned
user accounts to access the device.
17. The following windows are available from the Local User Interface with System Administrator login and authentication. These
windows provide standard system configuration or job management capability:
PagePack Passcode - Allows the System Administrator to enter a 4 digit "PagePack PIN" to enable a PagePack device to
•
work with metered supplies. Is accessible by selecting the following screens/buttons in order: [Machine Status] hard button
[Tools] button
accesses the PagePack Passcode screen and enters a valid PagePack PIN, the System Administrator can print out PagePack
courtesy prints by selecting the [Skip] button; however, if the number of PagePack courtesy prints requested exceeds the
allowable limit an appropriate error message will be displayed on the screen and the System Administrator will have to re-
enter a valid PagePack PIN.
Enter Cleaning Unit Passcode - Allows the System Administrator to enter a 4 digit passcode to temporarily extend a
•
Customer Replaceable Unit (CRU) when that CRU has reached its end of life. Is accessible by selecting the following
screens/buttons in order: [Machine Status] hard button
Unit Passcode] button.
Low Supply Warning - Allows the System Administrator to set when to receive low supply warnings for the ColorQube Ink
•
Sticks, Cleaning Unit, and Document Feed Roll. Is accessible by selecting the following screens/buttons in order: [Machine
Status] hard button
button.
Service Plan - Allows the System Administrator to set or change the Service Plan for the device. Is accessible by selecting the
•
following screens/buttons in order: [Machine Status] hard button
Plan] button.
Network Logs – Allows the System Administrator to download network logs to a USB drive for troubleshooting purposes. Is
•
accessible by selecting the following screens/buttons in order: [Machine Status] hard button
Settings] button
a basic or an enhanced level of network log information, and a separate screen will provide information on the completion
status of the download.
Downloaded network logs are always encrypted and require Xerox personnel to decrypt the logs before they can be read by
the System Administrator or other authorized persons.
USB Settings – Allows the System Administrator to enable/disable and set the configuration of the USB Printer Port
•
connectivity. Is accessible by selecting the following screens/buttons in order: [Machine Status] hard button
button
[Network Settings] button
Supply Counter Reset – Allows the System Administrator to manually reset the supply counter for a CRU on the device back
•
to 100% when that CRU is replaced. Is accessible by selecting the following screens/buttons in order: [Machine Status]
hard button
[Tools] button
18. The following windows are available to any authenticated and authorized user from the Local User Interface. These windows
provide standard machine services or job management capability:
Embedded Fax Batch Send Confirmation – Allows a user to either send an Embedded Fax job to a remote destination
•
immediately or include the job as part of a "batch" of Embedded Fax jobs sent to the same destination. Is accessible by
selecting the following screens/buttons in order: [Services Home] hard button
button when a user is submitting an Embedded Fax Send job to the same destination as a previously submitted "delayed
send" Embedded Fax job.
Workflow Scanning Authentication Required – Allows a user to enter the proper user credentials for a workflow scanning
•
job being sent to a network destination that requires user login. Is accessible by selecting the following screens/buttons in
order: [Services Home] hard button
workflow scanning job to a network destination that requires user login
Pausing an active job being processed by the device – Allows the user to pause an active copy, print, workflow scanning,
•
scan to email, Internet Fax or Embedded Fax job while it is being processed. Is accessible by selecting the [Stop] machine
hard button while a job is being processed by the device. Depending on the type of jobs being processed by the device when
the [Stop] button is selected, one of the following Pause windows will be displayed as appropriate to allow the user to
determine whether to delete or continue processing of the job: Scanning Pause window, Printing Pause window, Copy Only
(Scanning and Printing) Pause window, Scanning/Printing (Simultaneous Jobs) Pause window, Scanning Build Job
[Device Settings] button
[Tools] button
[User Interface Settings] button
[Advanced Settings] button
[Advanced Settings] button
[Troubleshooting] button
[Workflow Scanning] button
[Enter PagePack Passcode] button. Once the System Administrator
[Tools] button
[Tools] button
[Network Logs] button. The System Administrator can download either
[USB Settings] button.
[Resets] button
[Start] hard button when a user is submitting a
[OK] button.
[Device Settings] button
[General] button
[Low Supply Warning]
[Service Settings] button
[Tools] button
[Supply Counter Reset] button.
[Fax] feature button
[Enter Cleaning
[Service
[Network
[Tools]
[Start] hard
8