Xerox DocuColor 2060 Quick Reference Card
Browse online or download pdf Quick Reference Card for Software Xerox DocuColor 2060. Xerox DocuColor 2060 2 pages. Full color printing sytem
Also for Xerox DocuColor 2060: Operator's Manual (40 pages), Use Manual (2 pages), Recommended Materials List (4 pages), Recommended Materials List (5 pages), Planning Manual (22 pages)
Print Page
Product range/positioning
The Xerox DocuColor 2060 NPS/IPS is a full color printing system, fully
compatible with the IBM AFP Group 3 page printer with the Advanced
Function Image and Graphics (AFIG) option. The DocuColor 2060
NPS/IPS is targeted for up to 100,000 impressions per month. Usage
outside this range may vary the service frequency.
Speed
Data can be printed at rates up to 60 pages per minute. Throughput
rate can vary depending upon job complexity and system configuration.
Resolution
600 by 600 spots per inch (spi).
Paper handling
•
20 lb. (80 gsm) bond to 110 lb. (200 gsm) index cut-sheet weights
•
Paper sizes:
•
8.5 by 11 in. (216 by 279 mm) to
11 by 17 in. (216 by 432 mm), including A3
•
Trays 1 and 2: 12 by 18 in. (300 by 457 mm) SEF or 12.6 x
17.7 in. (320 by 450 mm) SEF, after the paper guides are
removed by a Xerox service representative
•
Trays 3 and 4: 7.2 to 12.6 in. (183 to 320 mm) LEF or 7.2 to
19.2 in. (183 by 488 mm) SEF
Input:
•
Trays 1 and 2 : 550 sheet capacity of 24 lb. (90 gsm) bond paper
•
Tray 3: 2200 sheet capacity of 24 lb. (90 gsm) bond paper
•
Optional High Capacity Feeder (Tray 4): 2500 sheet capacity of
24 lb. (90 gsm) bond paper
Output:
•
Offset Catch Tray: 500 sheets of 24 lb. (90 gsm) bond
•
Optional High Capacity Stacker: 3500 sheets of 24 lb. (90 gsm)
bond, up to 50 sheets stitched, offset capability. Capacity may
vary depending on the number of sheets stitched per set.
•
Optional High Capacity Stitcher Stacker: 2000 sheets of 24 lb. (90
gsm) bond, offset capability. Can send output to offset catch tray
or to the top tray.
System control module
(High performance Sun workstation)
The NPS/IPS printing system comes with the Sun Blade 1000
workstation.
Note: This configuration may change due to Xerox policy of staying
abreast of current technology.
•
Processor (system unit) containing:
•
Two UltraSPARC III 750 Mhz central processing unit (CPU)
modules
•
4 GB memory (four 1 GB DIMMs)
•
36 GB hard disk drive
•
DVD-ROM drive
•
3.5 inch diskette drive
•
Keyboard and mouse
•
Monitor
•
Optional Token Ring baord
•
Two Printer Controller Interface (PCI) boards installed in the
processor to interface with the print engine.
For channel connection to a host for IPDS printing, the system may use
a channel interface board that is connected to a channel cable
connector box.
An external 4 mm tape drive is available and recommended for backing
up site files. A typical color calibration file is 1.5 MB.
A second internal 36 GB hard disk drive is optional, as are two
additional external disks.
Printer module
•
Dry ink/toner cartridges: black, cyan, magenta, and yellow
•
Touch screen and control panel
•
Audio tones: attention, button selection, and fault
PSF environment
The system operates in the following PSF environments:
•
MVS
•
VM (channel-attached only)
•
VSE (channel-attached only)
•
OS/2
•
AS/400 (with TCP/IP only)
•
AIX
PDL compatibility
The system interprets the following text formats:
•
PostScript level 1
•
PostScript level 2
•
PCL5e
•
TIFF
•
ASCII
Space requirements
Controller:
Note: The following is presented as an example of typical space
requirements for Sun workstations.
Space requirements for the printer controller are 36 by 36 inches/
91 by 91 cm.
•
Processor
– 25 in. deep by 10 in. wide by 17.75 in. high
(63.5 cm by 25.4 cm by 45.1 cm)
•
Monitor
– 10 in. deep by 17.5 in. wide by 18.5 in. high
(25.4 cm by 44.5 cm by 47 cm)
•
Keyboard
– 7.5 in. deep by 20 in. wide
(19.1 cm by 50.8 cm)
•
Channel interface board and channel cable connector box (for
channel-attached systems)
– 9.7 in. deep by 27.1 in. wide
(24.6 cm by 68.8 cm)
Printer:
Space requirements (physical hardware and required service area)
for each of the printer configurations are:
•
DocuColor 2060 NPS/IPS printer
– 154.5 in. by 125 in. (390.5 cm by 316.7 cm)
•
DocuColor 2060 NPS/IPS printer with HCF (tray 4)
– 192.5 in. by 125 in. (487 cm by 316.7 cm)
•
DocuColor 2060 NPS/IPS printer with HCS
– 183.3 in. by 125 in. (464.3 cm by 316.7 cm)
•
DocuColor 2060 NPS/IPS printer with HCF and HCS)
– 221.3 in. by 125 in. (560.6 cm by 316.7 cm)
For additional space/configuration options, refer to the Xerox
DocuColor 2060 NPS/IPS Installation Planning Guide (Pub
#721P90520).
System connections
One of the following network communications systems may be used to
transport documents from the client workstation to the printer:
•
Ethernet LAN running TCP/IP, AppleTalk, or Novell NetWare
network protocol software.
•
Token Ring running TCP/IP or AppleTalk network protocol
software
•
Bus and tag channel connection, using a PCI board and control
unit
Note: DocuColor 2060 does not support multiple network interfaces
simultaneously.