Yamaha AW4416 Manual Supplement - Page 7

Browse online or download pdf Manual Supplement for Musical Instrument Yamaha AW4416. Yamaha AW4416 48 pages. Installing an internal hard disk
Also for Yamaha AW4416: Supplement Manual (1 pages), Tutorial (34 pages), Supplement Manual (20 pages), Manual (3 pages)

Print Page

ECHO

If this button is on, received control changes will

be "thru-ed" (retransmitted) without change from

the MIDI OUT connector/TO HOST connector/

option slot.

PARAMETER CHANGE

Here you can make transmission/reception set-

tings for system exclusive messages that control

the AW4416's parameters (parameter change

messages). Each button has the following func-

tion.

If this button is on, operating a parameter of the

AW4416 will cause the corresponding parameter

change to be transmitted.

If this button is on, receiving a parameter change

will cause the corresponding AW4416 parameter

to change.

ECHO

If this button is on, received parameter changes

will be "thru-ed" (retransmitted) without change

from the MIDI OUT connector/TO HOST con-

nector/option slot.

BULK

Here you can make settings for bulk data recep-

tion. If the BULK RX button is on, the AW4416

will be able to receive bulk dump data and mes-

sages requesting a bulk dump (bulk dump

requests).

MTC SYNC

When using MTC (MIDI Time Code) to synchro-

nize the AW4416 song with an external MIDI

device, this setting selects whether the AW4416

will function as the MTC master (MASTER button

on) or MTC slave (SLAVE button on).

In the previous version, the MTC MASTER indicator in

the level meter/counter was lit or dark depending on

whether MTC output from the MTC OUT connector

was turned on or off. However in version 2.0, MTC is

output from the MTC OUT connector at all times. For

this reason, the lit/dark status of the MTC MASTER

indicator now indicates the on/off state of MTC out-

put from the MIDI OUT connector/TO HOST con-

nector/option slot 2.

SYNC OFFSET

When using the AW4416 as an MTC slave, this

lets you shift the absolute time of the AW4416

relative to the received MTC. The range is "-

24:00:00:00.00" – "+24:00:00:00.00"

Tx CH (Transmit channel)

This speciﬁes the channel (1–16) of the MIDI

messages that will be transmitted from the

AW4416.

Rx CH (Receive channel)

This speciﬁes the channel (1–16) of the MIDI

messages that receive received by the AW4416.

MMC DEVICE

This sets the device ID (1–127) used to distin-

guish between devices when MMC (MIDI

Machine Control) messages are used to perform

remote control between the AW4416 and exter-

nal MIDI devices.

MMC MODE

Use the following three buttons to make settings

for MMC reception and transmission.

OFF button

If this button is on, the AW4416 will not transmit

or receive MMC.

MASTER button

If this button is on, the corresponding MMC

command will be transmitted from MIDI OUT/

TO HOST connector/option slot when you oper-

ate the transport of the AW4416.

SLAVE button

If this button is on, the AW4416 will obey MMC

commands received from MIDI IN/TO HOST

connector/option slot.

Tip!

In order to use MMC, the device ID of the AW4416

and the external MIDI device must match. The device

ID of the AW4416 is speciﬁed by the MMC DEVICE

setting ( 9 ).

SYNC AVERAGE

This sets the permissible range of variation in

MTC timing when using the AW4416 as an MTC

slave. Select one of the following three settings.

OFF button

If this button is on, the permissible range will be

the least, and the AW4416 will synchronize to

incoming MTC with the highest precision. How-

ever if MTC with signiﬁcant variation is received,

synchronization may be lost or become unstable.

This setting is suitable when two AW4416 units

are being operated in synchronization.

1 button/2 button

Turning on the 1 button will increase the permis-

sible range, and turning on the 2 button will set

the permissible range to the maximum setting.

These settings are suitable when an external

device with signiﬁcant variation in MTC (such as

a tape recorder or computer-based sequencer) is

used as the MTC master.

The SYNC AVERAGE setting is valid only when the

word clock source is set to "INT" (internal clock). If

the AW4416 is synchronized to an external clock,

operation will automatically be the same as when this

setting is OFF.

Version 2.0 Manual Supplement