Yamaha Piano Craft RX-E600 Owner's Manual - Page 2

Browse online or download pdf Owner's Manual for Receiver Yamaha Piano Craft RX-E600. Yamaha Piano Craft RX-E600 26 pages. Yamaha rx-e600: owners manual
Also for Yamaha Piano Craft RX-E600: Owner's Manual (23 pages)

Print Page

1. Specifications

CAUTION: READ THIS BEFORE OPERATING THIS UNIT

To assure the finest performance, please read this

manual carefully. Keep it in a safe place for future

reference.

Install this unit in a well ventilated, cool, dry, clean

place away from direct sunlight, heat sources, vibration,

dust, moisture or cold. In a cabinet, allow about 10 cm

(4 in.) of free space all around RX-E600 for adequate

ventilation.

Locate this unit away from other electrical appliances,

motors, or transformers to avoid humming sounds.

Do not expose this unit to sudden temperature changes

from cold to hot, nor locate this unit in an environment

with high humidity (i.e., a room with a humidifier) to

prevent condensation inside this unit, which may cause

an electrical shock, fire, damage to this unit, and/or

personal injury.

Avoid installing this unit in a location where foreign

objects may fall onto this unit or where this unit may be

exposed to liquid dripping or splashing. On the top of

this unit, do not place:

• Other components, as they may cause damage and/or

discoloration on the surface of this unit.

• Burning objects (i.e., candles), as they may cause fire,

damage to this unit, and/or personal injury.

• Containers with liquid in them, as they may fall, spilling

the liquid and causing an electrical shock to the user

and/or damage to this unit.

Do not cover this unit with a newspaper, tablecloth,

curtain, etc. in order not to obstruct heat radiation. If the

temperature inside this unit rises, it may cause fire,

damage to this unit, and/or personal injury.

Do not plug in this unit to a wall outlet until all

connections are complete.

Do not operate this unit upside-down. It may overheat,

possibly causing damage.

Do not use excessive force on switches, knobs and/or

cords.

When disconnecting the power cord from the wall

outlet, grasp the plug; do not pull the cord.

Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

Use only the voltage specified on this unit. Using this

unit with a higher voltage than specified is dangerous

and may cause fire, damage to this unit, and/or personal

injury. YAMAHA will not be held responsible for any

damage resulting from use of this unit with a voltage

other than as specified.

To prevent damage by lightning, disconnect the power

cord from the wall outlet during an electrical storm.

Do not attempt to modify or fix this unit. Contact

qualified YAMAHA service personnel when any service

is needed. The cabinet should never be opened for any

reason.

When not planning to use this unit for long periods of

time (i.e., vacation), disconnect the AC power plug from

the wall outlet.

Be sure to read the "Troubleshooting" section on

common operating errors before concluding that this

unit is faulty.

Before moving this unit, press STANDBY/ON to set the

unit in standby mode, then disconnect the AC power

plug from the wall outlet.

0102CRXE400(M).Cau.E

18 VOLTAGE SELECTOR (General model only)

The VOLTAGE SELECTOR on the rear panel of this

unit must be set for your local main voltage BEFORE

plugging into the AC main supply. Voltages are 110/120/

220/240 V AC, 50/60 Hz.

To reduce the risk of fire or electric shock, do not

expose this appliance to rain or moisture.

The unit is not disconnected from the AC power source

as long as it is connected to the wall outlet, even if this

unit itself is turned off. This state is called the standby

mode. In this state, this unit is designed to consume a

very small quantity of power.

CAUTION FOR CARRYING THE UNIT

Before carrying the unit, first remove the disc from

the unit, press STANDBY/ON to turn the unit off,

then disconnect the AC power plug from the wall

outlet.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT:

The wires in the mains lead are coloured in accordance

with the following code:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured

markings identifying the terminals in your plug,

proceed as follows: The wire which is coloured BLUE

must be connected to the terminal which is marked

with the letter N or coloured BLACK. The wire which

is coloured BROWN must be connected to the terminal

which is marked with the letter L or coloured RED.

Making sure that neither core is connected to the earth

terminal of the three pin plug.

For U.K. customers

If the socket outlets in the home are not suitable for the

plug supplied with this appliance, it should be cut off and

an appropriate 3 pin plug fitted. For details, refer to the

instructions described above.

Note: The plug severed from the mains lead must be

destroyed, as a plug with bared flexible cord is hazardous

if engaged in a live socket outlet.

CAUTION

Use of controls or adjustments or performance of

procedures other than those specified herein may

result in hazardous radiation exposure.

Laser component in this product is capable of

emitting radiation exceeding the limit for Class 1.

(U.S.A., Canada and General models)

The nameplate is located on the bottom of the unit.

2004.06.15, 19:04