Yamaha KAX-2500 Owner's Manual - Page 3

Browse online or download pdf Owner's Manual for Amplifier Yamaha KAX-2500. Yamaha KAX-2500 16 pages. Owner's manual

Print Page
Yamaha KAX-2500 Owner's Manual
Installation
Connect this unit's power cord only to an AC outlet of the type
●
stated in this Owner's Manual or as marked on the unit. Failure
to do so is a fire and electrical shock hazard.
Do not allow water to enter this unit or allow the unit to
●
become wet. Fire or electrical shock may result.
Do not place a container with liquid or small metal objects on
●
top of this unit. Liquid or metal objects inside this unit are a
fire and electrical shock hazard.
Do not place heavy objects, including this unit, on top of the
●
power cord. A damaged power cord is a fire and electrical
shock hazard. In particular, be careful not to place heavy
objects on a power cord covered by a carpet.
Be sure to connect to an appropriate outlet with a protective
●
grounding connection. Improper grounding can result in elec-
trical shock.
Operation
Do not scratch, bend, twist, pull, or heat the power cord. A dam-
●
aged power cord is a fire and electrical shock hazard.
Do not remove the unit's cover. You could receive an electrical
●
shock. If you think internal inspection, maintenance, or repair is
necessary, contact your dealer.
Installation
Keep this unit away from the following locations:
●
- Locations exposed to oil splashes or steam, such as near cook-
ing stoves, humidifiers, etc.
- Unstable surfaces, such as a wobbly table or slope.
- Locations exposed to excessive heat, such as inside a car with
all the windows closed, or places that receive direct sunlight.
- Locations subject to excessive humidity or dust accumulation.
Do not place the power cord close to a heater. It may melt, causing
●
fire or electrical shock.
Hold the power cord plug when disconnecting it from an AC out-
●
let. Never pull the cord. A damaged power cord is a potential fire
and electrical shock hazard.
Do not touch the power plug with wet hands. Doing so is a poten-
●
tial electrical shock hazard.
This unit has ventilation holes at the front and rear to prevent the
●
internal temperature rising too high. Do not block them. Blocked
ventilation holes are a fire hazard.
In particular, do not
- place the unit on its side or upside down,
- place the unit in any poorly-ventilated location such as a book-
case or closet (other than on the dedicated rack),
- cover the unit with a table cloth or place it on a carpet or bed.
Allow enough free space around the unit for normal ventilation.
●
This should be: 5 cm at the sides, 10 cm behind, and 10 cm above.
If the airflow is not adequate, the unit will heat up inside and may
cause a fire.
To mount several of these units in a standard EIA rack, refer to the
●
rack mounting instructions on page 11.
Precautions
— For safe operation —
WARNING
CAUTION
Do not modify the unit. Doing so is a fire and electrical shock haz-
●
ard.
If lightning begins to occur, turn off the power switch of the unit as
●
soon as possible, and unplug the power cable plug from the electri-
cal outlet.
If there is a possibility of lightning, do not touch the power cable
●
plug if it is still connected. Doing so may be an electrical shock
hazard.
In case an abnormality occurs during operation
If the power cord is damaged (i.e., cut or a bare wire is exposed),
●
ask your dealer for a replacement. Using the unit with a damaged
power cord is a fire and electrical shock hazard.
Should this unit be dropped or the cabinet be damaged, turn the
●
power switch off, remove the power plug from the AC outlet, and
contact your dealer. If you continue using the unit without heeding
this instruction, fire or electrical shock may result.
If you notice any abnormality, such as smoke, odor, or noise, or if
●
a foreign object or liquid gets inside the unit, turn it off immedi-
ately. Remove the power cord from the AC outlet. Consult your
dealer for repair. Using the unit in this condition is a fire and elec-
trical shock hazard.
To relocate the unit, turn the power switch off, remove the power
●
plug from the AC outlet, and remove all connecting cables. Dam-
aged cables may cause fire or electrical shock.
When setting up the product, make sure that the AC outlet you are
●
using is easily accessible. If some trouble or malfunction occurs,
immediately turn off the power switch and disconnect the plug
from the outlet. Even when the power switch is turned off, electric-
ity is still flowing to the product at the minimum level. When you
are not using the product for a long time, make sure to unplug the
power cord from the wall AC outlet.
Do not place the device in a location where it may come into con-
●
tact with corrosive gases or salt air. Doing so may result in mal-
function.
Operation
Use only speaker cables when connecting speakers to amplifier
●
outputs. Using other types of cables is a fire hazard.
Turn off all musical instruments, audio equipment, and speakers
●
when connecting to this unit. Use the correct connecting cables
and connect as specified.
Always lower the volume control to minimum before turning on
●
the power to this unit. A sudden blast of sound may damage your
hearing.
Do not use this amplifier for any purpose other than driving loud-
●
speakers.
If you know you will not use this unit for a long period of time,
●
such as when going on vacation, remove the power plug from the
AC outlet. Leaving it connected is a potential fire hazard.
3