Zanussi ZGNN645X User Manual - Page 6

Browse online or download pdf User Manual for Hob Zanussi ZGNN645X. Zanussi ZGNN645X 21 pages.
Also for Zanussi ZGNN645X: User Manual (21 pages)

Print Page

Model .......................................

PNC .........................................

Serial number ...........................

IMPORTANT SAFETY REQUIREMENTS

This hob must be installed in accordance with the

Gas Safety (Installation and Use) Regulations

(Current Edition) and the IEE Wiring Regulations

(Current Edition).

For appliances installed in the Republic of Ireland

please refer to NSAI- Domestic Gas Installation I.S.

813 Current Editions and the ETCI Rules for

Electrical Installations.

Provision for ventilation

Detailed recommendations are contained in the

following British Standards Codes Of Practice:

B.S. 6172/B.S. 5440, Par. 2 and B.S. 6891

Current Editions.

The hob should not be installed in a bed sitting

room with a volume of less than 20 m³. If it is

installed in a room of volume less than 5 m³ an air

vent of effective area of 100 cm² is required. If it is

installed in a room of volume between 5 m³ and 10

m³ an air vent of effective area of 50 cm² is

required, while if the volume exceeds 11 m³ no air

vent is required.

However, if the room has a door which opens

directly to the outside no air vent is required even if

the volume is between 5 m³ and 11 m³.

If there are other fuel burning appliances in the

same room, B.S. 5440 Part 2 Current Edition,

should be consulted to determine the requisite air

vent requirements.

For appliances installed in the Republic of Ireland

please refer to the NSAI- Domestic Gas Installation

I.S. 813 Current Editions Table Four.

Location

The hob may be located in a kitchen, a kitchen/

diner or bed sitting room (with a volume greater

than 20 m³), but not in a bathroom or shower room.

The minimum distance combustible material can be

fitted above the hob in line with the edges of the

hob is 400 mm. If it is fitted below 400 mm a space

of 50 mm must be allowed from the edges of the

hob.

For appliances installed in the Republic of Ireland

please refer to NSAI- Domestic Gas Installation I.S

813 Current Edition Section 7- Permitted

Locations of Appliance.

GAS CONNECTION

WARNING! Any gas installation must

be carried out by a GAS SAFE

Make sure that, once the hob is installed, it is easily

accessible for the engineer in the event of a

breakdown.

The manufacturer will not accept liability, should the

above instructions or any of the other safety

instructions incorporated in this instruction booklet

be ignored.

On the end of the shaft, which includes the G 1/2"

threaded elbow, adjustment is fixed so that the

washer is fitted between the components as shown

in the diagram. Screw the parts together without

using excessive force.

B C

A. End of shaft with nut

B. Washer supplied with the appliance

C. Elbow supplied with the appliance

Connection to the gas supply should be with either

rigid or semi-rigid pipe, i.e. steel or copper.

The connection should be suitable for connecting

to R 1/2 (1/2 BSP male thread).

When the final connection has been made, it is

essential that a thorough leak test is carried out on

the hob and installation.

Make sure that the main connection pipe does not

exert any strain on the hob.

If you use flexible metal pipes make sure that they

agree to ISO 10380 and ISO 10807 standards. Be

careful they do not come in touch with mobile parts

or they are not squeezed. Also be careful when the

hob is put together with an oven.

CAUTION! It is important to install the

elbow correctly, with the shoulder on

the end of the thread, fitted to the hob

connecting pipe.

CAUTION! Failure to ensure the

correct assembly will cause leakage of

gas.

CAUTION! Make sure that the gas

supply pressure of the appliance

obeys the recommended values.