Alean ABE series User Manual

Browse online or download pdf User Manual for Security Sensors Alean ABE series. Alean ABE series 1 pages. Triplicate photoelectric beam detector

Print Page
TRIPLICATE PHOTOELECTRIC BEAM DETECTOR
TRIPLICATE PHOTOELECTRIC BEAM DETECTOR
User Manual
1
Parts description
Connection Terminal
LED indicators
Tamper
Beam alignment
Level Indicator
Lens
Vertical Adjustable
Screw
Horizontal Adjusting
Dial
Cover locking screw
Cover
2
Setting notice
Where blocks (such as trees or place for hanging clothes)
are between the receiver and the sender while installing..
In case of using mangy groups of detectors
when long distance protection to avoid the
mutual disturbance of light beams.
Protection distance
3
Mounting Method
1. Loosen the fixed screw
2.Break out the knock-out and pull
and remove the cover.
wire through.
4 Connecting wires to the terminal.
Free
Power
Free
Tamper switch
Transmitter
Alarm output
Free
Power
Tamper switch
Receiver
5. Fix the cover after beam alignment is adjusted .
Pole mounting:
1.Break out the wire hole on
2.Remove the cover
the bracket then pull out the
wires.
4
Beam Adjustment
1.Remove the cover, apply the power.
2.Adjust the horizontal adjustment dial and vertical adjustment screw,
to make the most LEDs ON, the 5th LED must be ON, otherwise
please readjust. More than 7 lit LEDs is recommended.
.
Caution
The more LED indicators light, the higher
of the precision of the beam alignment would be.
Wiring Hole
Beam interruption
Power (green) is on when the beam is transmitting
Time Adjustment
Voltage Testing
Hole
LEVEL becomes brighter when more LEDs light
in alignment.
ALARM
red is on when create alarm activation
GOOD (green) is on when beams are aligned,
and off when beams are not well aligned.
After alignment, the fifth alignment LED of receiver
must be on, otherwise you have to continue the
alignment. Recommend the 7th or more LED
indicators on.
Where the sunlight light and automobile headlight
Where installation base
Shine directly.
is unstable.
The optical axis can be adjusted within
0
0
horizontal direction +90 , vertical direction +10
Horizontal direction +180(+ 90)
0
0
Vertical direction +10
alarm shop
Protection distance
Dispersion
50m
1.5m
75m
2.3m
100m
3.0m
125m
3.8m
150m
4.5m
180m
5.4m
200m
6.0m
250m
7.5m
3.Mount the detector on the wall.
15mm
Knockout
The wiring distance
Diameter
DC12V
Voltage
2
0.5mm (
0.8)
300m
2
0.75mm (
1.0)
400m
1.25mm (
1.2)
700m
2.0mm (
1.6)
1000m
Back to back installation (Refer to the figure below.)
3.Fix the base plate on the bra cket.
Vertical Adjustment Screw
Horizontal Adjustment Dial
Left
Right
Voltage Meter testing method:
1. Insert the probes of the voltage meter to the testing hole (Pay attention to the polarity)
2. Adjust the dial horizontally and vertically to obtain the largest voltage.
3. If 1.2V or above cannot be acquired, you have to continue to adjust. Top output
can be up to 1.8V(1.5v or above is recommended to prevent false alarm in severe
environment ).
DISTANCE
Caution
After the optical axis angle alignment, the 5th
LED indicator of receiver must be on,otherwise
you have to continue the alignment.
Recommend the 7th or more LED indicators light.
5
Beam interruption time adjustment
3. 306msec
6
Operation confirmation
After installation, confirm correct
operation by suitable walk tests.
Refer to the LED indication of the
right form during the walking test.
0
7
Troubleshooting
Symptom
Transmitter LED dose not light.
Receiver LED dose not light
Alarm LED dose not light, even
when beams are blocked.
When the beams are blocked,
the receiver LED lights is ON ,
but not alarm.
The alarm indication lamp of receiver
is always on.
Intermittent alarm
DV24V
600m
8
800m
Specification
1400m
2000m
Outdoor
Range
Indoor
Beam characteristics
Heater
Interruption period
Power input
Current consumption
Alarm period
Alarm output
Tamper switch
Operating temperature
Environment humidity
Alignment angle
Mounting
Weight
Appearance
9
Mounting, bracket and measurement
Recommend mounting
m
PHOTOELECTRIC DETECTOR
1. 50msec
4. 408msec
Condition
Transmitter
Transmitting
Watching
Receiver
Alarm
Possible Cause
Improper voltage supplied.
.
Improper voltage supplied.
1.Beams reflect to the receiver by
other objects.
2. 3 beams are not interdicte d
Simultaneously.
3. Shading light time is too short.
1.Wring is short circuit.
2. Wiring point is not good.
1. Optical axis is not properly adjusted.
2. There are blocks between the
transmitter and receiver.
3. The detector cover or strained slick
are dirty.
1. Bad wiring.
2. Supplied voltage can't reach 12V
3. Movable blocks between
the transmitter and the receiver.
4. The installation base is unstable.
5. Improper lens direction.
6. Blocked by other moving objects.
7.The interruption time is too short.
8.5 Lens do not light when uncover
50m
100m
75m
125m
150m
300m
225m
375m
Pulsed infrared triplicate beams
Options
50~700msec(selectable)
DC12~24V/AC11~18V
70mA max
80mA max
2sec(+1)nominal
NO.NC relay (AC/DC30V 0.5A max)
N.C (DC24V, 0.5A max)
-25 ~+55
5%-95% relative humidity
20 (+10 )vertical, 180 (+90 )horizontal
Wall or pole
1900g(Both transmitter and receiver)
PC Resin(Black)
T-Shaped Backet
T-100
100 120mm
T- 00
00 120mm
I-Shaped Bracket
100mm
L-Shaped Backet
00mm
80 75mm
Bracket
DC 10V
2. 80msec
5. 700msec
Indication
Green LED is ON
GOOD-LEVEL Indication is ON
Alarm indication lamp is ON
Remedy
Check the power supply and wiring.
Check the power supply and wiring.
1. Remove the reflecting object or
change optical axis direction.
2. Shade 3 beam
3. Prolong the shading time.
Checking wiring and connection spot.
1. Adjust the optical axis.
2. Remove the blocks.
3. Polish with the soft cloth.
1. Check wiring.
2. Check the power supply.
3. Remove the blocks or relocate.
4. Fix the mounting.
5. Adjust the lens directio n.
6. Adjust interruption time or
change installing position.
7.Readjust interruption time.
8.Readjust the lens direction to
obtain fine alignment.
150m
180m
200m
250m
540m
600m
750m
450m
90mA max
100mA max
I-100
285mm
I- 00
External measurement