Clarke PP9ND Operating & Maintenance Manual - Page 4

Browse online or download pdf Operating & Maintenance Manual for Air Compressor Clarke PP9ND. Clarke PP9ND 10 pages. Air compressor

Clarke PP9ND Operating & Maintenance Manual
FOR YOUR SAFETY
WARNING
As with all machinery, there are certain hazards involved with their operation and use.
Exercising respect and caution will considerably lessen the risk of personal injury.
However, if normal safety precautions are overlooked, or ignored, personal injury to
the operator, or damage to property may result.
It is in your own interest to read and pay attention to the following rules:
General Precautions
ALWAYS
ensure that all individuals using the compressor have read and fully understand the
Operating Instructions supplied.
Stop the engine and ensure the pressure is expelled from the air receiver BEFORE carrying
out any maintenance.
ensure that there is adequate ventilation when spraying flammable materials e.g.
cellulose paint, and keep clear of any possible source of ignition.
protect yourself. Think carefully about any potential hazards which may be created by using
the air compressor and use the appropriate protection. e.g.Goggles will protect your eyes
from flying particles. Face masks will protect you against paint spray and/or fumes.
consult paint manufacturers instructions for safety and usage, before spraying
ensure that the air supply is turned off at the machine outlet and all pressurised air from
the machine and other equipment attached to it, is expelled BEFORE disconnecting air
hoses or other equipment.
make sure that children and animals are kept well away from the compressor and any
equipment attached to it.
ensure that any equipment or tool used in conjunction with your compressor, has a
safety working pressure exceeding that of the machine.
NEVER
direct a jet of air at people or animals, and NEVER discharge compressed air against
the skin. COMPRESSED AIR CAN BE DANGEROUS!
leave pressure in the receiver overnight, or when transporting.
adjust, or tamper with the safety valves. The maximum pressure is factory set, and clearly
marked on the machine.
operate in wet or damp conditions. Keep the machine dry at all times. Similarly, a clean
atmosphere will ensure efficient operation. Do not use in dusty or otherwise dirty locations.
touch the machine until it has cooled down...some of the metal parts can become
quite hot during operation.
operate your compressor with any guards removed.
- 4 -
PUMP PARTS
No.
Description
1
Air Filter Assy ....................................................................... FN317013000
2
Head Bolt M6x45 ................................................................ FN014002021
3
Cylinder Head .................................................................... FN116001001
4
Spacer ................................................................................. FN116060015
5
Heat Shield ......................................................................... FN116060016
6
Screw M6x70 ...................................................................... FN014002029
7
Washer 6.5x18 .................................................................... FN014005044
8
Screw M5x15 ...................................................................... FN014013042
9
Elbow ................................................................................... FN011015000
10
Gasket ................................................................................. FN116022009
11
Valve plate ......................................................................... FN116022100
12
Gasket ................................................................................. FN116022010
13
Cylinder ............................................................................... FN116022001
14
Screw M8x20 ...................................................................... FN014011064
15
O-Ring ................................................................................. FN010114000
16
Piston Ring Set .................................................................... FN216022002
17
Piston ................................................................................... FN116022004
18
Gudgeon Pin ...................................................................... FN116022040
19
Circlip .................................................................................. FN015001000
20
Piston Complete ................................................................ FN416022004
21
Con-Rod ............................................................................. FN116091021
22
Dipstick ................................................................................ FN012035000
23
Washer ................................................................................ FN010072000
24
Screw M6x10 ...................................................................... FN014013024
25
End Casing ......................................................................... FN016032014
26
Screw ................................................................................... FN014006083
27
Gasket ................................................................................. FN116001025
28
Screw ................................................................................... FN014022001
29
Eccentric ............................................................................ FN116060005
30
Key ....................................................................................... FN116060006
31
Crankshaft .......................................................................... FN116060001
32
Bearing ................................................................................ FN033058000
33
Seal ...................................................................................... FN010060000
34
Crankcase .......................................................................... FN116060011
35
Casing ................................................................................. FN116060003
36
Screw M5x20 ...................................................................... FN014013046
37
Screw M5x25 ...................................................................... FN014013045
38
Fan ....................................................................................... FN016060002
39
End Casing ......................................................................... FN116060004
40
Shield ................................................................................... FN116060010
41
Gasket Kit ............................................................................ FN216GA0001
- 17 -
Part No.