Directed Xpresskit DBALL2 Installation And Quick Reference Manual - Page 5

Browse online or download pdf Installation And Quick Reference Manual for Door locks Directed Xpresskit DBALL2. Directed Xpresskit DBALL2 16 pages. Ford5 remote start ready (rsr) installation
Also for Directed Xpresskit DBALL2: Installation Manual (12 pages), Installation Manual (19 pages), Installation Manual (18 pages), Manual (14 pages), Installation Manual (13 pages), Installation Manual (14 pages), Installation Manual (19 pages), Installation Manual (16 pages), Installation Manual (20 pages), Installation Manual (15 pages), Installation Manual (18 pages), Installation Manual (16 pages), Installation Manual (18 pages), Installation Manual (16 pages), Manual (19 pages)

Print Page
Directed Xpresskit DBALL2 Installation And Quick Reference Manual
Platform: DBALL2
Firmware: GM6
Installation Type 3a, T-Harness THGM610 Rev. 1 & 2, T-01 (without RFLCHGM)
WARNING!
We recommend using the Wiring Diagram (
RFLCHGM) will draw 15-20mA more on the vehicle, when it is parked and the engine is turned off.
Using Wiring Diagrams (
without
wire opening. To preserve OEM remote starter functionality, use the Wiring Diagram (
Use connectors
D2D
labeled GM6
only
Ignition
Barrel
To vehicle
6-pin connector
T-01
T-02
T-01
Buick Enclave
Buick Lucerne
Cadillac CTS
Cadillac CTS Coupe
Cadillac CTS Wagon
Cadillac DTS
Chevrolet Caprice
Chevrolet Impala
Chevrolet Monte Carlo
Chevrolet Traverse
GMC Acadia
Pontiac G8
Saturn Outlook
If the RAP Off wire is not connected, the radio will turn OFF but some lights will remain ON in the central console for 10 minutes. Connect this wire
[1]
(Green/Black, pin 2/12) to the driver door sense trigger (Gray/Black) to avoid the issue. RAP Off: Refer to page 9 for wire color and location.
Only required if no OEM hood pin.
[2]
with
RFLCHGM) on page 3, especially if the vehicle is not used daily. The Wiring Diagram (
RFLCHGM) can deactivate OEM remote starter functionality, OEM fob and smart phones, due to the accessory
To
Immobilizer
Control
Module (ICM)
(under ignition switch,
black connector)
(+) Ignition Status Output: Pink:7
Ignition
n/a: Black/White:1
Connector
(-) RAP Off: Green/Black:2
[1]
n/a: Violet/Brown:8
n/a: Violet/Green:9
(-) Driver
Door Sense
Trigger
[1]
NOT
USED
with
RFLCHGM) on page 3.
(+) Ignition Input
To
Immobilizer
Control
Module (ICM)
(vehicle side)
RF
Prog. Button
LED
T-Harness
THGM610
(Optional)
CAN High
CAN Low
Rev.: 20151221
Page 5
without
(-) Ground
(-) Ground
(+) 12V
(+) 12V
(-) Parking Lights
(-) Parking Lights
(-) Hood Status Input
[2]
Hood Pin
n/a: White/Black
Remote Start Safety
Override Switch
(+) 12V
DBALL/
RX
(-) Ground
DBALL2
P#: XKD2D65
TX
NOT USED
Cut away the 4-pin
connector and connect
the two wires to the
OBDII 16-pin connector.
CAN High: Tan/Black, pin 6
1
8
9
16
CAN Low: Tan, pin 14
Diagnostic connector
OBDII (connector side view)
© 2015 Directed. All rights reserved.