Nikon Eclipse Ti Series Instructions Manual - Page 13

Browse online or download pdf Instructions Manual for Camera Accessories Nikon Eclipse Ti Series. Nikon Eclipse Ti Series 19 pages. Differential i nterference contrast attachment

Print Page

Assembly

Before

assembly,

be sure

read all

warnings

and precautions

the

instruction manual for the microscope.

Install the

sextuple

Dlc

nosepiece, perfect focus with

motorized

nosepiece,

analyzer,

Dlc

polarizer, and

condenser

your

microscope by pertorming

steps

through

below.

you

reciuire'a very

frecise vibration

direction adjustmenl,

perform step

as well.

For

delails

on assembling the microscope, installing the system

condenser,

perfect focus

with notorized

nosepaece

etc',

refer

the

instruction manual provided with

the

microscope, and

the

.T|-ND6-E

sexuple

motorized

Dlc

nosepiece",

or'Tl-cr-E

motorized condenser

turrer

are

bèing used,

also

refer to

ihe

instruction

manual supplied with

the

motorized units

lor

series.

the

DIC

focus with motorized

Place

the

s€xtuple

Dlc

nosepiece on

the

square groove

the microscope's

nosepiece mount, sliding

the

nosepiece toward

the

rear of

the.microscope

far as

will

go.

Tighten

the

bolts with a

neiajonat

wrencn

secure

lhe nosepiece. Fhis step

easier

perform

yo-u

remóve the stage

first.)

the

DIC

Lower the

focusing mechanism' screw

the

ob.iectives into

the revolving

nosepiece so that the obiectives are

::ojfl^Îj]l"t"uting

powerwhen the

revolving nosepiece is rotated

initre

ctòcrwise oirection

1*'nen

uieweo

from above).

Dtc

the

Remov€ the dummy slider

locateddirectly

below

the

Dlc objective.

Replace the dummy slider with a

Dlc

prism

that

corresponds with

the Drc

obje;tive. lttote

that ttró type

of Drb

prism useo oepenos

onìne

wnen ustng the

T-42 analyzer

Remove the

dust-proof

slider on

the

microscope

focusing mechanism

and insert

the analyzer. The

analyzer

enters the optical path at

the

second

clickstop

iosition.

pulling

the

slider

ori

ínì rir.t

clickstop position

removes the

analyzer

from the

opticat'pattr ano

places the

empty

hole

the

opticat

oath.

Typically,

the

analyzer

is installed so that the

vibration direction adjustment lever

the

right,

but

can also

be installed with

thè vibration direction adiustment lever

the

left,

you

prefer.

When u6íng the epi-fl fllter

tunet

attachod wlth the analyzer

block

Insert the epi-fl filter turret along

the attachment

groove

froó the

right of the

microscope.

Remove

the

filter

block port cover and

secuie the

epi-fl filter

túrret

with

screws

the

right

and

left with

the

hexagonal

wrench.

Insert

theEnalyzer

block along

the

guide

groove,

and

then attach

the

filter

block port

cover

again.

objective.)

Figure

4-1

lf the

system condenser

is attached

to the condenser

holder,

remove

it.

lt is

not possible

instalt

the

DIC

polariz6r

while the condenser

attached.

Mount

the

DIC

polarizer

on the

condenser

mount of

the

microscope,

aligning the

DIC

polarizer positioning

pin with

the

groove on

the condenser mount. Turn

the

fixing

ring

fix

the

DIC

polarizer

in place.

When using the T-A2 analyzer