Clas Ohlson SC329D Quick Start Manual

Browse online or download pdf Quick Start Manual for Accessories Clas Ohlson SC329D. Clas Ohlson SC329D 4 pages. Wireless doorbell

Print Page

Wireless Doorbell

Article number: 36-1725, model: SC329D

•

Wireless doorbell with belt clip.

•

Including transmitter and receiver.

•

Several different signals.

•

Range about 25 metres.

•

Operated on one CR2032 (included) and two LR6 (not included).

Please read the entire instruction manual before using and save it for

future use. We apologise for any text or photo errors and any changes of

technical data. If you have any questions concerning technical problems

please contact our Customer Service Department.

Inserting Batteries

Push button (transmitter) operates on one Lithium battery (CR2032, 3V)

that is included. Battery is mounted and the product is ready to use when

delivered.

How to change battery when needed: Loosen the push buttons back-

side carefully using a screwdriver. Loosen the screw for the battery

attachment (the shackle) place the battery with the (+) against the battery

attachment (the shackle) tighten the screw and put back the backside.

The doorbell (receiver) operates on 2x LR6 batteries (not included).

1. Remove the battery cover on the back.

2. Insert 2x LR6 batteries according to the markings on the battery

compartment.

3. The buzzer sounds twice to indicate that it is ready to use and to

read the radio frequency from the push button (see chapter Setting

of radio frequency).

4. Close the battery cover.

Mounting

Find a suitable location and test the signal range before drilling the holes.

Push button (transmitter)

Loosen the push buttons backside carefully using a screwdriver. Use the

two holes on the backside as template and mark desired location close

by the door. Drill two holes and mount the push button with the supplied

screws (use plugs if needed) or double-sided adhesive tape (included).

Note! Do not mount the push button on a metal surface; it will reduce the

range considerably.

Doorbell (receiver)

Hang it up in the belt clip or use the hole for hanging underneath the belt

clip. Mount a screw where the doorbell is to be hang, leave about 3 mm

between the wall and screwhead.

GREAT BRITAIN For consumer contact, please visit www.clasohlson.co.uk and click on customer service. Internet: www.clasohlson.co.uk

ENGLISH

Signal selection

Set the signal underneath the backside of the push button. With a button

marked S. Westminster is preset, press the button to change to the next

and then the next etc. Switch between 8 different melodies and sounds.

Note! You can purchase an additional push button and use it by the

backdoor etc. Set it on a different signal then the first to know which door

your visitor is ringing from.

Setting of radio frequency

The wireless doorbell is set on a radio frequency from the factory, change

frequency if disturbance occur from other units in the neighbourhood.

The push buttons radio frequency can be changed by the shackle on

the backside and the doorbell (receiver) sets the correct radio frequency

automatically. No need to manually changing it.

Change the push buttons radio frequency like this:

1. Loosen the push buttons backside carefully using a screwdriver.

2. There are frequency settings with four different shackles (1, 2, 3, 4)

that together gives 16 different settings.

3. Change the setting by removing one or more shackles. Remove the

batteries from the doorbell (receiver) and put them back again. The

buzzer sounds twice to indicate that it is ready to read the new radio

frequency.

4. Press the push button after changing a setting and put back the

batteries. The doorbell will sound and indicates therefore that it is

controlled by the set frequency on the push button and saves it in the

memory.

5. Testing the function.

Function

Press the push button once and it will send a wireless signal to the door-

bell. The doorbell will sound and the LED lights up once and stops when

the set signal ends. The signal is not repeated unless you hold in the push

button, release the push button and press again if you wish to repeat the

signal.

Volume control

The volume setting is in the doorbells battery compartment.

LO low – HI high

Note! Helpful Suggestions:

Do not mount the push button on a metal frame etc. test the function/

location before the final mounting.

Do not expose the push button or receiver to water or extreme heat.

Do not mix new/old batteries or different types of batteries. Remove

the batteries if the product is not to be used for a longer period of time

(to avoid leakage).

Use alkaline batteries in the doorbell that will last long, remove used

batteries to avoid leakage.

Warning! Use only batteries of recommended type placing them correctly

according to the (+) and (-) marking.

Troubleshooting

No sound but the LED blinks when the push button is pressed in:

The distance is too far between the units: change location!

Units are set on different radio frequency: control the shackle on all

units!

No sound and no indication from the LED when the push button is

pressed in:

Bad battery in the push button: change battery!

Battery is placed incorrectly in the push button: place the battery

correctly (+ outwards)!

The doorbell sounds without the push button being pressed in:

Wireless products in the surrounding area affect the doorbell: change

frequency (see above)!

Specifications

Push button (transmitter):

Battery:

CR2032 Lithium (3V)

Current Consumption:

3.0mA (while transmitting)

0.003mA (in standby mode)

Doorbell (receiverp)

Battery:

2x LR6

Current Consumption:

100mA (while receiving)

0. 3mA (in standby mode)

Operating temperature: -10°C to +40°C

Range:

Up to 25 metres (outdoor, unobstructed area)

Sound:

8 different sounds

Frequency settings:

16 different options.

Size:

94x61x30 mm (doorbell)

85x33x26 mm (push button)

Disposal

Follow local ordinances when disposing of this product. If you are unsure

about how to dispose of this product contact your municipality.