Arnica Hydra Rain PLUS Instruction Manual - Page 13
Browse online or download pdf Instruction Manual for Vacuum Cleaner Arnica Hydra Rain PLUS. Arnica Hydra Rain PLUS 16 pages. Shampoo vacuum cleaner with water filter
Print Page
• Replace water filter body (Figure 12)
NEVER FILL THE CONTAINER WITH CLEAN WATER WHILE
PREPARING APPLIANCE FOR SHAMPOOING
•Fill the shampoo resarvoir with clean water (use C4 water level
indicator as reference) and shampoo (dose is mentioned on
shampoo bottle) Place the shampoo reservoir onto the wheel
group (Figure 15)
• Place the container onto the shampoo reservoir and the motor
unit onto the container. Lock the clamps. (Figure 4)
• Insert the short shampoo hose (C3) to the shampoo reservoir
(Figure 16) and to connector on the back side of motor unit.
(Figure 17)
• Attach the long shampoo hose to the shampoo trigger. Other
side of the shampoo hose will be connected to the connector
(A3) on the motor unit.
• Fix the shampoo trigger to the handgrip of the suction hose.
• Attach the long shampoo hose to the suction hose and suction
tubes by means of the clips.
• Attach the shampoo nozzle (F1) to the suction tubes or directly on
to the handgrip. Mini wetsweep can be attached to the handgrip
only. For shampooing the carpets, mats and floor use nozzle, for
shampooing the armchairs, sofas,curtains, car upholstary, etc. use
miniwetsweep. fixing it directly to the handgrip.
• Insert the plug into the wall socket.
• Press the pump switch and operate pump to inject water and
shampoo mix onto the surface to be treated.
• The shampoo and water is injected from the shampoo reservoir
by pump and sprayed through a nozzle on to the surface to be
cleaned. The shampoo penetrates the fibers, dissolving even
the most stubborn dirt. Wait at least three minutes to allow
the shampoo to soak in completely.
• Press the on/off switch which activates the extraction function
and pass over the surface while pump is not operating. For
cleaning the upholstery, sucking up the dirty water, spraying
the shampoo and water mix functions can be made at the
same time operating on/off switch and pump. If bubble starts
to come out of the nozzle, turn off the appliance immediately
and empty the container, check the amount of the shampoo
mixed into water.
• Once the container is full with dirty liquid, the float blocks the
suction operation automatically and motor gets noisier. At the
time switch off the vacuum cleaner and pump IMMEDIATELY,
pull out the plug, remove the suction hose (E3) from the hose
connector detach the motor unit and empty the container.
• For cleaning the hard floors like tiles, bricks, marble, ext. fit the
hard floor adapter on to the large wet cleaning head sliding it in
to place from left to right Proceed as described in this section
dealing with spraying and sucking liquids.
• Using the crevice nozzle, you can soak the water discharge
from dish washer or washing machine, spilling of liquids,
refrigerators and freezers defrosting. Attach the crevice nozzle
to the handgrip and switch on for vacuuming liquids.
CAUTION: If you don't use your vacuum cleaner according to
the instructions written above; there is a risk of excess foam
occurring and the excess foam might be ejected from the hepa
filter. When you experience a situation like this, you should,
turn off the machine unplug, empty the water tank, clean the
water filter body and dry it. Then, you should also remove the
Hepa Filter and dry it. Wash the foam filter located on the float
group and dry it as well. Wait 1 or 2 hours to dry the foam
inside the motor.
VI. CLEANING AND MAINTENANCE
• Always switch the appliance off and remove the mains plug
from the wall socket before starting any maintenance or
cleaning operations.
• Always empty, clean and dry the container after use.
• After wet cleaning, always suck clean water without shampoo
a few minutes for cleaning the
accessories, suction tubes and hose group and than suck air
for drying them.
• To ensure perfect hygiene and length the working life of vacuum
cleaner, never leave wet and dirt inside the container.
• Before emptying dirt and waste liquid remove suction hose of
hose group and lift Motor Unit by pulling the clip locks.
• The foam filter can be washed warm, soapy water or running
water. Dry it throughly before planing on to float case. Don't
wash foam filter at washing machine with hot water.
• Clean and check the float valve inside the float case moves
freely in it's housing. For checking the float, lift up the Motor
Unit and shake it.
• Replace the dust bag when it is full of dust
• The cleanness of hepa filter filter should be checked pe-
riodically. Clean the filter if it is not clean. This filter loses
its characteristics after a certain usage period and requires
replacing.
To clean the Turbo Brush
» The cleanness of the turbo brush should be checked periodically.
According your usage and type of dirt soaked by brush ropes, hairs
fibres and similar dirts abstract the spiral brush bar and spiral
brush bar could not turn properly. For these reason periodically
look at the bottom side of the turbo brush for checking the turning
of the spiral brush bar after operating the vacuum cleaner. If it
doesn't move freely clean the turbo brush.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
Children should be supervised to ensure that they do not play
with the appliance.
Unless management and supervision regarding the device
are ensured by a person responsible for safety of the
devices, this device isn't designed to be used by physically
and mentally disabled people (including children) or by
people who are lack of experience and knowledge.
Children must be supervised in order to ensure keeping
them away from the device.
13