Blake UK BLAPSU11F Instruction Manual - Page 3

Browse online or download pdf Instruction Manual for Power Supply Blake UK BLAPSU11F. Blake UK BLAPSU11F 4 pages. 1 or 2 way lte filtered (5g & 4g) power supply f type

Print Page

System equipotential bonding:

Distribution systems supplying signals to more than one household should comply with the safety requirements

of EN 60728-11. This effectively requires earthed equipotential bonding of the system. (The use of isolated

outlet plates is no longer recommended since they compromise screening integrity and allow ingress of

interference.) Bonding may be effected using a PROBAR equipotential bonding bar.

Output protection:

The power unit is internally protected against output short-circuit. If this protection operates, the power indicator

LED colour will change from green to red to indicate a fault condition. To reset the protection, disconnect the unit

from the mains and allow at least one minute for cooling before re-applying power.

Related Products:

Installation Products

PROCON01: F Male Twist-On +O-Ring - RG6/100

PROCON02: F Male Twist-On +O-Ring Black - RG6/100

PROCON12: F Male Crimp-On Black - RG6/100

PROCON22: F Male Snap Seal / Compression - RG6/100

Product

Number of Outputs

Signal Frequency Range

Insertion Loss

Signal

Isolation Between Outputs

Output Voltage

Output Current Rating

Output Protection

Power and Status Indicator

Input Filter Characteristics

Filter specifications

Mains Power Requirement

Operating Temperature Range

Standards Compliance

Overheating:

These amplifiers are intended for use in moderate climates only. They should not be used in tropical

regions. The recommended ventilation clearances and other precautions given in the relevant section of this

instruction leaflet should be observed to prevent overheating. No unit should be fixed where it is likely to

become smothered by soft furnishing fabrics such as curtains, or by thermal insulation material in a roof

space or building void. Mains powered equipment should not be left resting on a carpet

Water and fire risks:

The power supply is not waterproof. It is intended for indoor use only and must not be fixed where it could

be exposed to dripping or splashing water. Objects containing liquids should not be placed on or near the

appliance. To prevent risk of fire, no object with a naked flame should be placed on or near any of the

appliances, or its associated wiring.

Mains plug and disconnection from the supply:

The appliance is supplied with a standard fused plug fitted. If this is unsuitable, refer to the instructions

below. If you need to change the fuse in the fitted plug, a 3 Amp fuse to BS 1362 carrying the ASTA or BSI

approval mark must be used. Always replace the plastic fuse carrier when renewing the fuse. The plug (or

other means of disconnection from the supply, if used) should remain readily accessible for operation when

necessary. The LED power indicator on this equipment should not be regarded as providing reliable

indication of supply disconnection.

Changing the plug:

If the fitted mains plug is not suitable for the socket-outlets in use, it should be cut off and a new plug fitted...

Wiring the new plug: Instructions supplied with the new plug should be followed. The brown wire must be

connected to the live (L) terminal of the plug and the blue wire to the neutral (N) terminal. Neither wire

should be connected to the earth (E) terminal of a 3-pin plug (the appliance does not require an earth

connection). Ensure that the cord grip in the plug is correctly used and clamps the sheath of the cord firmly.

Fuse Rating: If the new plug is a fused type, the fuse fitted should be rated at not more than 3 Amp.

Caution: The old plug should be destroyed immediately since it would be dangerous if plugged into a live

socket.

BLAPSU11F

5-694MHz

<3dB

(Typical)

+12V Regulated DC(±0.6V)

100mA max

Withstands Indefinite Output Short-Circuit Without Damage

Green-Normal, Red- Short

LTE (5G/4G) > 30 dB rejection

BS EN 50083 (Standard 3 filter)

230V 50Hz at 3A (3VA)

-20 -- +50°C

Safety: EN IEC62368 EMC: EN 50083

Safety Instructions

Link to Website:

www.blake-uk.com/install

www.blake-uk.com/procon01

www.blake-uk.com/procon02

www.blake-uk.com/procon12

www.blake-uk.com/procon22

BLAPSU12F

<4dB

>20dB