Camille Bauer KINAX 2W2 Operating Instructions - Page 3

Browse online or download pdf Operating Instructions for Transmitter Camille Bauer KINAX 2W2. Camille Bauer KINAX 2W2 4 pages. Programmable transmitter for angular position
Also for Camille Bauer KINAX 2W2: Operating Instructions (4 pages)

Print Page

4.5 low

120°

Fig. 6. KINAX 2W2 with special drive shaft at front and at rear.

Front: dia. 1/4ʺ, length 12 mm [0.472ʺ]. Rear: dia. 2 mm, length 6 mm [0.078ʺ,

0.236ʺ].

6. Mounting

Mechanical mounting

All versions of the transmitter can be mounted either directly or by means of 3

mounting clips to the item being measured. Both methods of mounting and the

relevant drilling and cut-out plans can be seen from Table:

Mounting versions

4.5 low

Mounting/positioning

Three M3 screws are needed for the "directly" mounted versions and three M4

screws for those "with clamps". The screws are not supplied, because the required

length varies according to the thickness of the mounting surface.

When deciding where to install the transmitter (measuring

location), take care that the "Ambient conditions" given in

Section "5. Technical data" are not exceeded.

Angular position transmitters of the KINAX 2W2 range do not require a mechani-

cal zero position mark (however, this is made if required by the customer). After

mounting, the transmitter can be moved to any position and conﬁ gured using the

2W2 software. A power supply connection to the KINAX 2W2 is not required in

order to use the 2W2 conﬁ guration software (Fig. 7; AUX switch on the PK 610 in

the ON position.

The angular position transmitter must only be programmed

outside of the Ex areal!

Ancillary cable

Programming

connector

KINAX 2W2

Fig. 7. Connection diagram programming

1.5

Ø1/4˝

–0.005

(6.35 g6)

–0.014

26.1

Drilling and cut-out diagrams

for mounting transmitters)

Load max. [Ω] with

output 20 mA

900

600

Power supply [V]

+ 0.025

[1.574]

Interface

PK 610

OFF

OFF: Power supply

by measuring output

(Fig. 10)

ON: Power supply

provided by PC

If you programm the KINAX 2W2 with a connected power

supply, then the switch on the interface PK610 must be im-

perative switched to OFF. If this is ignored, this can lead to the

destruction of the device.

Positioning procedure for the KINAX 2W2

1. Mount the angular position transmitter and mechanically connect it to the object

to be measured. Connect the KINAX 2W2 to the programming device according

to Fig. 7. Start the 2W2 conﬁ guration software. If necessary, conﬁ gure the device

with the required measuring range data.

2. Place the measuring device in a deﬁ ned position (prefereably the zero position).

3. Select the "Adjustment" menu item under "SERVICE" in the conﬁ guration

software. In the "Mechanical position" window enter the current angle of

the measuring device and then select "Adjust". The measuring device is now

conﬁ gured for the deﬁ ned angle.

7. Electrical connections

For connecting the external wires, the transmitter has 2 soldering pins at the back

(Fig. 8) or a connecting print with screw terminals (Fig. 9). The soldering posts

sufﬁ ce Protection Class IP 00 acc. to IEC 60 529.

Fig. 8. Connection with soldering plugs Fig. 9. Connection with screw terminals

Note that, ...

... the data required to carry out the prescribed measurement must

correspond to those marked on the nameplate of the KINAX 2W2

(Range, Output, Supply Voltage)!

... the total loop resistance connected to the output (receiver plus

leads) does not exceed the maximum permissible value R

"Measuring output" in Section "5. Technical data" for the maximum

values of R

... twisted cores must be use for the measured variable input and

output leads and routed as far away as possible from power cables!

In all other respects, observe all local regulations when selecting the

type of electrical cable and installing them!

In the case of "Intrinsically safe" explosion-proof versions

[Ex ia] IIC, the supplementary information given on the EC-Type-

Examination Certiﬁ cate, the EN 60 079-14 and also local regulations

applicable to electrical installations in explosion hazard areas must

be taken into account!

Do not excessively heat the soldering posts!

Solder using a small pencil bit soldering iron!

–

ext

= DC power supply H = 12 to 33 V resp. H = 12 to 30 V with Ex version

= External resistance

ext.

Fig. 10. Connection diagrams for 2-wire connection.

8. Setting the beginning and end

Fine adjustment

he analog output can be ﬁ nely adjusted using the 2W2 conﬁ guration software.

Select the menu item "Adjustment" under "SERVICE". In the "Analog output"

window, the zero position and the end value can now be adjusted.

Procedure:

1. Put the transmitter into operation and connect the programming device according

to Fig. 7 (AUX switch on the PK 610 in the OFF position).

2. Place the measuring device in the zero position, i.e. in the position in which the

KINAX 2W2 should output 4 mA. Adjust with the "ZERO" virtual knob until the

output is correct.

Programming

connector

Screw terminals

Soldering plugs

ext.

Soldering

plugs

Screw terminals

–

ext

Programming

connector

Cable-tie

clamp

! See

ext.

Cable-tie

clamp