Camille Bauer SINEAX V604s Operating Instructions Manual - Page 5

Browse online or download pdf Operating Instructions Manual for Transmitter Camille Bauer SINEAX V604s. Camille Bauer SINEAX V604s 19 pages. Universal signal converter
Also for Camille Bauer SINEAX V604s: Safety Instructions (13 pages)

Print Page

Output settings

Limit

Gain/offset trimming

Inversion

Relay contact output

Contact

1 pole, normally open contact

Switching capacity

AC: 2 A / 250 V AC

DC: 2 A / 30 V

Bus/programming connection

Interface, protocol

RS-485, Modbus RTU

Baudrate

9,6...115,2 kBaud, adjustable

Transmission behaviour

Measured variables

for the outputs

• Input 1

• Input 2

• Input 1 + Input 2

• Input 1 – Input 2

• Input 2 – Input 1

• Input 1 · Input 2

• Minimum value, maximum

• Sensor redundancy

Transmission function

Linear,

user-speciﬁ c via

basic value table

(24 basic values per measured

variable)

Settling time:

Adjustable 1...30 s

Limit values and monitoring

Number of limit values 2

Measured variables for

limit values

• Input 1

• Input 2

• Measured variable for outputs

• Input 1 – Input 2

• Input 2 – Input 1

Functions

Absolute amount

Gradient dx/dt (e.g. temperature

gradient monitoring)

Time delay

Adjustable 0...3600 s

Signaling

Relay contact, alarm LED,

Status 1

Sensor breakage and

short circuit monitoring measuring input

Signalling

Relay contact, alarm LED,

Status 1

Output value in case of a fault

Other monitoring operations

Drift monitoring

Monitoring of measured value

between 2 input sensors for a

certain period of time (e.g. due to

different sensor response times).

If this time is exceeded, an alarm

is signalled.

(See Limit values 1 and 2)

Camille Bauer

value

or mean value of Input 1

and Input 2

Input 1 or Input 2

(e.g. drift monitoring in case of

2 sensors)

(e.g. drift monitoring in case of

2 sensors)

Operating instructions V604s Be

Sensor redundancy

Measurement with 2 temperature

sensors; if Sensor 1 fails (fault)

Sensor 2 is activated for bridg-

ing (see measuring variable for

outputs).

Alarm signalling

Relay contact

With closed contact,

the yellow LED shines,

invertible

Alarm LED

Time delay

Adjustable 0...60 s

Output value

in case of a fault

For sensor breakage and short

circuit, value adjustable –10...

110%

Power supply

Rated voltage UN

24...230 V DC *

100...230 V AC, 45...400 Hz

* In case of a power supply voltage >125 V DC, the power

supply circuit must contain an external fuse

Power consumption

>3 W or 7 VA

Displays at the instrument

LED

Color

green

green ﬂ ashing

ERR

red

yellow

Conﬁ guration, programming

Operation with PC software «CB-Manager»

Accuracies

(according to EN/IEC 60770-1)

Reference conditions

Ambient temperature

23 °C ± 2 K

Power supply

24 V DC

Reference value

Span

Settings

Input 1: Direct voltage mV,

0...1000 mV

Output 1: 4...20 mA, burden

resistance 300 Ω

Mains frequency 50 Hz,

Setting time 1 s

Input 2, output 2, relay, monitor-

ing off or not active, for voltage

output: range 0...10 V, burden

resistance 2 kΩ

Installation position

Vertically, detached

Basic accuracy

At reference conditions ±0.1%

Other types of measurement and input ranges:

RTD Pt100, Ni100

±0.1% ±0.2 K

Resistance measurement ±0,1% ±0.1 Ω

TC Type K, E, J, T, N, L, U ±0.1% ±0.4 K,

measurement value > –100 °C

TC Type R, S

±0.1% ±2.4 K

TC Type B

±0.1% ±2.4 K,

measurement value > 300°C

Tolerance

±15%

Function

Power on

Communication activ

Alarm

Relay on