Divis CH 03515 User Manual

Browse online or download pdf User Manual for Security Camera Divis CH 03515. Divis CH 03515 2 pages. Ir dome camera

Print Page

CH 03515

IR DOME Camera

C A U T I O N

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

To prevent fire or shock hazard, do not expose the unit to rain or moisture. The symbol is intended to alert

the user to the presence of important operating and maintenance (servicing) instructions in the literature

accompanying the appliance.

SA 1966

The symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the

product's enclosure that may be sufficient magnitude to constitute a risk of electric shock to persons.

SA 1965

Installation

1. Opening the dome : Push the latch button.

2. Removing the dome : Lift the dome case.

3. Camera installation & Lens adjustment.

1) Fix the mount bracket with supplied

screw on ceiling or wall mount.

Note : The camera front sign is on the

mount bracket.

2) Attach the main body to the mount

bracket by rotating it.

3) By turning the ①(Tele-Wide) knob,

you can access a range of focal lengths

4) Since then, by turning the

②(Near-Far) knob, you can set the focus

5) Reassemble dome case.

axis

CAUTION:

To prevent electric shocks and risk of fire hazards,

DO NOT use other than specified power source.

Caution

1. Do not attempt to disassemble the camera.

In order to prevent electric shock, do not remove screws or cover.

2. Handle the camera with care.

The camera could be damaged by improper handling or storage

3. Do not expose the camera to rain or moisture, or try to operate in wet

areas.

Take immediate action if the camera becomes wet. Turn the power off and

request service to qualified personnel. Moisture can damage the camera and

also create a risk of electric shock.

4. Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when dirty. In case the dirt is hard to

remove, use a mild detergent and wipe gently.

5. Never point the camera toward the sun.

Whether the camera is used outdoor or not, never point it toward the sun. Use

with caution when operating the camera in the vicinity of spot lights or other

bright lights and light reflecting objects.

6. Do not operate the camera beyond its temperature, humidity, or power

source ratings.

Do not use the camera in an extreme environment where high temperature or

high humidity exists. Use the camera under conditions where temperatures are

between 14 F~122 F (-10 C~+50 C), and humidity is below 85%,

WARNING

This equipment has been tested and found to comply with the limits for a Class A. Digital

device. Pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with

the instruction manual, it may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be required

to correct the interference at own expense.

CAUTION

Any changes or modifications in construction of this device which are not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment.

Diagram & Adjustment

1. Pan adjustment : Grasp the lens cover and then adjust direction to the

right or left. ('D' -180˚~+180˚)

2. Tilt adjustment : Grasp the lens cover and then adjust direction to the

up or down ('A' : 18˚~90˚ or 'B' 21˚~90˚)

3. Roll adjustment : grasp the lens cover and then rotate ('C' : -180˚~+180)

SCREW TP1

4X30 3EA

Main Product

User Manual

Angle Adjustment

Removing Mount Bracket

1. Push the button inside of main

body and turn the main body

counterclockwise.

2. Detach the main body from mount

Composition

Mount Bracket

Screws & Anchor