dji Focus Quick Start Manual - Page 2
Browse online or download pdf Quick Start Manual for Camera Accessories dji Focus. dji Focus 2 pages. Accessory support frame
Also for dji Focus: Quick Start Manual (2 pages), Quick Start Manual (6 pages)
Print Page
DJI FOCUS
Quick Start Guide
Install the Antenna
Screw on the antenna.
Mount the Motor
To mount the motor onto your camera support rod:
1. Loosen the knob on the quick-release mount
and slide the motor onto the support rod.
The motor gear can be mounted on either side of the
●
motor. To remove the gear, loosen the knob at the
center of the gear.
The motor supports a 15 mm rod diameter by default.
●
To mount it on a 19 mm rod, slide the step-down
adapters off the clamp.
2. Tighten the knob, ensuring that the motor gear
and lens gear ring make good contact.
3. Connect the communication port on the motor
to an external power source using the supplied
power cable. If you are using the Ronin-M,
connect the motor to the P-TAP Accessory
power port on the Ronin-M.
DJI Focus can work in wireless mode or cable mode. To
use cable mode, connect the communication ports on
the remote controller and motor using the data cable.
Ensure the motor is mounted firmly.
●
DO NOT touch the motor when it is rotating.
●
Cable mode will take precedence over wireless mode.
●
Attach the Neck Strap
Insert the neck strap connector
while pulling on the button.
Ensure the neck strap is attached securely.
●
Calibrate the Motor
Turn on the remote controller by holding down the
power button for 2 seconds.
If your camera lens has mechanical limits, use Auto
calibration. Otherwise, use Manual-Remote or
Manual-Hand calibration.
50.0%
Calibrate
Menu
Auto
Select Calibrate > Auto (Shortcut: Press the 'A' and
'B' buttons together). The motor gear will rotate in
both directions in turn to locate the mechanical
limits of your camera lens. When the calibration is
complete, select Back to apply the calibration or
Stop to cancel.
Manual-Remote
Select Calibrate > Manual-Remote > Start to
begin. Press the up arrow to rotate the lens in one
direction, and select OK when it reaches the desired
upper limit. Next, press the down arrow to rotate
the lens in the other direction, and select OK when it
Motor Power Cable
reaches the desired lower limit.
The motor will automatically reserve a 1mm margin at both mechanical limits for protection.
●
Mount the Lens Gear Ring
Used with the Zenmuse X5
DJI Focus is fully compatible with the Zenmuse X5 series gimbal and camera. To allow communication
between the two devices, connect the communication port on the Focus remote controller to the
CAN Bus port on the Inspire 1 remote controller using the dedicated CAN Bus cable.
Select Menu > Aperture > On to enable the Aperture Control.
To switch from focus control to aperture control, press the 'D' button and then follow the instructions in
the DJI GO app to operate the focus wheel.
Ensure that the Zenmuse X5 camera is set in AF mode.
●
The remote controller overrides the in-app controls. You will not be able to adjust the focus or aperture in the DJI GO app.
●
You can purchase the dedicated CAN Bus cable on the DJI Store.
●
Basic Operation
Manual-Hand
Select Calibrate > Manual-Hand >
Start to begin. Rotate the lens
Turn the focus wheel to control the focus,
manually to the desired upper and
zoom or iris of your camera lens.
lower limits of your camera lens,
and select OK to confirm the limits.
Refer to the user manual for more information.
http://www.dji.com/product/focus
※This Quick Start Guide is subject to change without prior notice.
Mount the lens gear ring if you are not
using a cinema lens with gear rings.
1. Choose the lens gear ring that best fits
2
your camera lens.
2. Tighten the screw.
1
Ensure that the lens gear ring and camera lens
●
make good contact.
Ensure the lens gear ring screw is installed
●
properly to allow an unobstructed full range of
motion.