Altronix AL1042ULADA Installation Manual - Page 4

Browse online or download pdf Installation Manual for Extender Altronix AL1042ULADA. Altronix AL1042ULADA 17 pages. Nac power extenders
Also for Altronix AL1042ULADA: Installation Manual (3 pages), Application Manual (8 pages), Application Manual (8 pages)

Print Page

Altronix AL1042ULADA Installation Manual

6. Connect FACP output to the desired AL842LGK logic board inputs, and notification appliances to the desired AL842LGK

logic board outputs (see Application Guide).

Note: The 2-wire horn/strobe sync mode will only synchronize horns, horn/strobes, strobes with

synchronization capability.

7. For connection of smoke detectors, digital dialer see Optional Hookup Diagram, pg. 8.

Outputs must be programmed independently (OUT1 - OUT4)

Function

Input to Output Follower

Mode

Temporal Code 3 Mode

Steady Mode

For the above modes Dip Switch 4 determines which Input controls the corresponding output:

Switch 4 in the ON position causes output(s) to be controlled by input 1.

Switch 4 in the OFF position causes output(s) to be controlled by input 2.

Switch Positions

Function

Amseco Sync

Mode*

Faraday

Sync Mode*

Gentex

Sync Mode

Gentex is a registered trademark of

Gentex Corporation.

System Sensor

Sync Mode*

1, 2, 4

System Sensor is a registered

trademark of Honeywell.

CooperWheelock

Sync Mode*

2, 3, 4

CooperWheelock is a

registered trademark of

Cooper Wheelock.

Note: The AL1042ULADA will only synchronize horns, horn/strobes and strobes that contain synchronization capability.

Contact signal manufacturer for more detailed info. The same synchronization mode must be selected for all outputs.

Note: It is required to control visual notification appliances (strobes) via input 1 [IN1] and audible notification

appliances (horns) via input 2 [IN2]. This allows audible notification appliances (horns) to be silenced while

visual notification appliances (strobes) continue to operate.

- 4 -

Output Programming Selection Table:

Switch Positions

OFF

2, 3

1, 2

1, 2, 3

Sync Mode Selection Table:

Descriptions

OFF

This mode is designed to work with the Amseco series of horns, strobes, and

1, 3,

horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the flash timing of the strobe, and silencing the horns of the horn/

strobe combination over a two-wire circuit while leaving strobes active.

This mode is designed to work with the Faraday series of horns, strobes, and horn/

strobes to provide a means of synchronizing the Temporal-coded horns, synchroniz-

2, 4

1, 3

ing the flash timing of the strobe, and silencing the horns of the horn/strobe combi-

nation over a two-wire circuit while leaving strobes active.

This mode is designed to work with the Gentex

1, 2,

strobes to provide a means of synchronizing the Temporal-coded horns, synchroniz-

3, 4

ing the flash timing of the strobe, and silencing the horns of the horn/strobe combi-

nation over a two-wire circuit while leaving strobes active.

This mode is designed to work with the System Sensor

horn/strobes to provide a means of synchronizing the Temporal-coded horns, syn-

chronizing the one-second flash timing of the strobe, and silencing the horns of the

horn/strobe combination over a two-wire circuit while leaving strobes active.

This mode is designed to work with the CooperWheelock series of horns, strobes,

and horn/strobes to provide a means of synchronizing the Temporal-coded horns,

synchronizing the one-second flash timing of the strobe, and silencing the horns of

the horn/strobe combination over a two-wire circuit while leaving strobes active.

Descriptions

Output follows signal it receives from the corresponding input

(i.e. FACP Sync module - maintains synchronization of

notification appliance circuit).

Enables Temporal Code 3 signal generation output.

This mode will accept a steady or a pulsing input.

A steady output signal will be generated.

This mode will accept steady or pulsing input.

AL842LGK Board

(Output Dip Switches)

series of horns, strobes, and horn/

series of horns, strobes, and

INPUT SELECT

TEMPORAL

STROBE SYNC

IN>OUT SYNC

AL1042ULADA