Alula 2GIG RE214T Manual - Page 9

Browse online or download pdf Manual for Smoke Alarm Alula 2GIG RE214T. Alula 2GIG RE214T 13 pages.

Print Page

condition).

The Smoke Alarms will be silenced for a period

of approximately 10 minutes. The red light on

the cover of the Smoke Alarm will flash every

8 seconds to indicate that the unit has been

silenced.

2. The Smoke Alarm will reset to normal

sensitivity at the end of the silenced period

(10 minutes). If additional silenced time is

required, simply push the Test/Silence button

again.

3. If kitchen usage/layout is such that there

are an unacceptable level of nuisance alarms,

re-locate the Smoke Alarm further away where

it will be less affected by cooking fumes etc.

We recommend the use of a Heat Alarm in the

Kitchen area to avoid such nuisance alarms.

7.3 Power Supply Monitoring

7.3.1 What to do when an Alarm is beeping:

A Smoke Alarm is beeping about every 48

seconds with the yellow light flashing at the

same time:

- Replace the Battery or Batteries.

7.3.2 Battery Replacement

When the battery power is low and replacement

is necessary, the Smoke Alarm will "beep" and

the yellow light will flash at the same time

about once every 48 seconds for at least

7 days. The battery must then be replaced.

Also, replace the battery if the Alarm does

not sound when the Test Button is pressed.

When you replace the battery you must press

the Test button to check that the Alarm is

functioning correctly. Only replace the battery

with: Panasonic CR123A Batteries.

Dispose of used battery promptly. Keep away

from children. Do not disassemble and do not

dispose of in fire

Replacement batteries can be purchased at

your local hardware store.

Warning!

CONSTANT EXPOSURES TO HIGH OR LOW

TEMPERATURES OR HIGH HUMIDITY MAY

REDUCE BATTERY LIFE.

Use only batteries specified in marking. Use

of a different battery may have a detrimental

effect on Alarm operation.

These cells are intended for use at ordinary

temperatures

where

temperature excursions are not expected to

exceed 100°C (212°F).

Prolonged periods of alarm will also reduce

battery life.

Caution: The battery used in this device

may present a fire or chemical burn hazard

if mistreated. Do not recharge, disassemble,

heat above 100°C (212°F) or dispose of in fire.

anticipated

high

Replace battery with Panasonic CR123A, use

of another battery may present a risk of fire

or explosion.

7.4 Cleaning your Alarm

Clean your Alarm regularly. Use a soft bristle

brush or the brush attachment of your vacuum

cleaner to remove dust and cobwebs from the

side slots where the smoke enters. To clean

the cover, wipe with a damp cloth and dry

thoroughly.

WARNING: Do not paint your Alarm.

Other than the maintenance and cleaning

described in this leaflet, no other customer

servicing of this product is required. Repairs,

when needed, must be performed by the

manufacturer.

7.5 Chamber Cleaning

Cleaning or replacing of the chamber cover

should only be carried out by suitably trained

personal.

1. Remove the Alarm from the mounting plate.

2. Remove the battery or batteries.

3. With a flat screwdriver unclip the three

cover clip points (see figure 8a).

4. Remove the cover (see figure 8b).

5. Unplug the thermistor by holding the

thermistor PCB and pulling the pins out of

the sockets (see figure 8c).

6. To remove the chamber top turn the

chamber anti-clockwise approx. 15 degrees

(see figure 8d).

7. Blow out or use a soft bristled brush to

remove dust and dirt form the chamber

base.

8. Fit a new chamber top and clip in place by

turning clock-wise 15 degrees.

9. Insert the thermistor PCB into the sockets

and ensure the thermistor is perpendicular

to the chamber (see figure 8e).

10. Place the cover back on the Alarm taking

care to ensure the thermistor is protruding

out the cover (see figure 8f).

11. Replace the battery / batteries and reattach

to the mounting plate.

12. Press the test button to ensure the Alarm is

working correctly.

Figure 8a