DKS 1520 series Installation And Owner's Manual - Page 9
Browse online or download pdf Installation And Owner's Manual for IP Access Controllers DKS 1520 series. DKS 1520 series 16 pages. Stand alone card readers or controller
Also for DKS 1520 series: Manual (2 pages)
Print Page
Before You Start Programming: IMPORTANT! Make sure the 1520 has power and we suggest that you become familiar with
programming instructions before beginning any programming.
2.1 Re-Programming the Master Code
The Master Code has been pre-programmed at the factory to 9999. This programming sequence re-programs the MASTER
CODE if desired. The master code is the four-digit number required to gain access to the system memory. You MUST know the
master code before programming ANY features.
Important Note:
After re-programming the master code, write it down and keep it in a safe place. There is no way of retrieving
the master code after it has been programmed in. If you forget it, you will have to program in a new one but all other previously
programmed information will remain intact.
Step 1. Remove the keypad mounting plate (see section 1.3) to access the Master Code push button.
(1520 must have power) Press the Master Code push button ONCE.
Step 2. Enter a four-digit master code using the keypad, then press "
Step 3. Re-install the keypad mounting plate. Write down master code and keep it in a secure place.
2.2 Relay Strike Time
The relay strike time sets the amount of time that the relay in the 1520 remains activated after a valid card (device) code is
received. Relay strike times can be programmed from 1/4 second - enter 0 0 * in step 2, up to 99 seconds - enter 9 9 * in step 2.
Factory setting for Relay is 01 (1 Second).
2.3 Date and Time
Set the time of the day with a four-digit number (hr/min). For example, 8:30 is entered as 0830; 11:45 is entered as 1145.
When entering the MONTH, January = 01 and December = 12. The day of the month is always entered as a two-digit number;
1st day of the month is entered as 01, the 20th day is entered as 20, etc.
The YEAR is entered with the last two digits of the current year; 2014 = 14, 2015 = 15, etc.
The DAY OF THE WEEK is entered as a single digit; Sunday = 1, Monday = 2 .........Saturday = 7.
Note: The time and date must be programmed to allow transactions, real time printing and anti-pass back to work correctly.
1520-065-E-7-16
SECTION 2 - PROGRAMMING
Actual keystrokes used on keypad:
Same keystrokes as written in this manual: [ _ _ _ _
1. Press
0 3 and enter the MASTER CODE. [
*
2. Enter the two-digit strike time (00-99), then press
3. Press 0 # TOGETHER to end. [0 # (beeeeeep)]
1. Press
3 3 and enter the MASTER CODE. [
*
2. Enter the four-digit time of day (Hr/Min), then press
3. Enter 0
for AM OR enter 1
*
4. Enter the two-digit month (01 to 12), then press
5. Enter the two-digit day of the month (01 to 31), then press
6. Enter the two-digit year (14,15... etc), then press
7. Enter the day of the week (1-7), then press
Sun =1, Mon = 2, Tue = 3, Wed = 4, Thu = 5, Fri = 6, Sat = 7.
Programming sequence automatically finished after "Long beep".
" (A short beep will be heard).
*
any four numbers
?
?
?
0 3 _ _ _ _ (beep)]
*
. [ _ _
*
3 3 _ _ _ _ (beep)]
*
. [ _ _ _ _
*
for PM. [ _
(beep)]
*
*
. [ _ _
*
. [ _ _
*
. [ _
(Long beeeep)]
*
*
Master Code Push Button
?
"BEEP"
Then press
(beep)]
*
(beep)]
*
(beep)]
*
(beep)]
*
. [ _ _
(beep)]
*
*
(beep)]
*
7