3M Multimedia Projector MP8740 Quick Start Manual - Page 2

Browse online or download pdf Quick Start Manual for Projector 3M Multimedia Projector MP8740. 3M Multimedia Projector MP8740 2 pages.

Print Page
3M MP8730/MP8740 Multimedia Projector Quick Setup Instructions
Project Packout
Multimedia Projector
Power Cord
3-Conductor
110V – US
Video/Audio Cable
220V – UK, Europe
Packout Items not Shown:
•
PS/2 mouse cable .............. (1)
•
ADB mouse cable ............. (1)
•
Serial mouse cable ............ (1)
•
Stereo mini-jack ................ (1)

Remote Control Transmitter

STANDBY / ON button
Set main power switch to ON.
Press and hold STANDBY/ON button for
projector mode (lamp on) or standby
mode (lamp off).
FOCUS button
Press +/- to adjust image sharpness.
ZOOM button
Press +/- to adjust image size.
Note: If needed, move projector
closer/further from screen.
POSITION ON
POSITION button
Press and light POSITION button.
Move DISK PAD to adjust horizontal/
vertical image position.
DISK PAD
Select mode, then move DISK PAD to
RESET
position image, navigate menus or control
mouse functions. To select the mode:
• Press and light POSITION button for
position mode.
• Press and light MENU ON button for
menu mode.
MENU ON button
Press and light MENU ON button to
display the Main Menu. Move DISK PAD
to select menu and/or adjust screen
values.
BLANK ON button
Press BLANK to display a blank
background with no image. Press again to
return the image to the screen.
INPUT buttons
RGB 1/2: Select computer video input
(RGB1
RGB2
RGB1).
VIDEO 1/2: Select video inputs
(VIDEO1
VIDEO2
VIDEO1).
Remote Control Transmitter
(batteries included)
VGA Cable
Adapter
(15-15 pin M/M)
with dip switch
MUTE button
Press MUTE to switch the audio
sound ON or OFF
VOLUME button
Press +/- to adjust internal/external speaker
volume.
STANDBY/ON
MUTE
LASER POINTER
Press and hold down button to project laser
pointer.
CAUTION
To prevent injury to eyesight, do not point
FOCUS
ZOOM
VOLUME
laser beam at other persons or look directly
into laser beam.
LASER
LEFT MOUSE
button
Backside
of Remote
RIGHT
MENU ON
MOUSE ON
RESET / RIGHT MOUSE button
RESET: When a menu is being displayed,
BLANK
TIMER
press RESET to return menu value to factory
setting.
RGB1/2
VIDEO1/2
RIGHT MOUSE: When computer image is
being displayed, press for right mouse button
INPUT
function.
MOUSE ON button
Press MOUSE ON button to activate mouse
mode. Move DISK PAD to control mouse
functions.
TIMER ON / OFF button
Press TIMER to display and start the timer as
set in OPT menu setting. Note: Timer will not
display on a blank screen. To remove TIMER
display press again.

Projector Startup

Video Cable
(S-Video mini
DIN4-pin)
Projector Startup Procedure
1.
Make all cable connections and line hookups with the power off.
2.
Turn the POWER SWITCH
3.
Move the LENS SHUTTER CONTROL
4.
Press the STANDBY/ON button
The ON indicator will blink green during warm-up and lamp ignition.
5.
Adjust the screen size using the ZOOM button
6.
Adjust the focus using the FOCUS button
7.
Turn on all connected equipment. The method of connecting various equipment, see section 2.3.
8.
Press the INPUT button
on the remote to select the source of the signal to be projected on the screen. The selected signal
input is displayed at the bottom right of the screen. The display will show the last selected input source
before power was turned off.
Projector Shutdown Procedure
1
.
Hold the STANDBY/ON button
turns off. After approximately 1 minute, the fan stops and the indicator stays orange.
2.
Turn the MAIN POWER SWITCH
Do not turn off the POWER SWITCH before pressing the STANDBY/ON button. After the STANDBY/ON
button is pressed, the fan rotates for about 1 minute to cool the projector.
3.
Close the LENS SHUTTER . Push up on the lens cover switch to close.
4.
Disconnect cables.
FOCUS
ZOOM
CLOSE
OPEN
of the projector on. The ON indicator will light up orange.
CLOSE
to the open position.
OPEN
. The ON indicator blinks (green) and then lights (green).
.
ZOOM
.
FOCUS
on the projector or the INPUT SELECT (VIDEO or RGB) button
for 3-5 seconds. The ON indicator blinks orange and the lamp
of the projector off.
Caution
CLOSE
OPEN