AKO AKO-D1460 Series Installation Instructions - Page 2

Browse online or download pdf Installation Instructions for Thermostat AKO AKO-D1460 Series. AKO AKO-D1460 Series 2 pages.

Print Page
Programming Menu (parameters)
Access to set point and programming
After 20 seconds with no key being pressed, the equipment will return to the previous level. If you are on level 3, the changes will not be saved.
5 sec.
10 sec.
t
SET
SET
Temperature
Release SET
Release SET
Indication
to access the
to access
set point
programming
Temperature
Indication
Table of parameters and messages
Def. column shows factory-set default parameters. Those marked with * are variable parameters depending on the application chosen in the wizard (see Start-up ). Unless otherwise stated, temperatures are expressed in °C.
AKO-D1460x
AKO-D1461x
AKO-D1462x
AKO-D1463x
AKO-D1464x
CONTROL
Description
Values Min. Def. Max.
With NTC
*
Temperature Adjustment (Set Point)
rE
SP
(ºC / ºF)
-50.0
(limits depending on probe type)
-
With PTC
C0
Calibrating probe 1 (Offset)
(ºC / ºF)
-20.0
0.0
C1
Probe 1 differential (Histeresis)
(ºC / ºF)
0.1
2.0
Upper blocking of the set point
With NTC
99.0
C2
(ºC / ºF)
C3
(cannot be set above this value)
With PTC
-
C3
Lower blocking of the set point (cannot be set below this value)
(ºC / ºF)
-50.0 -50.0
Type of delay for protection of the compressor:
C4
0=OFF/ON (since the last disconnection);
0
0
1=OFF-ON/ON-OFF (since the last shut-down /start-up)
Protection delay time
C5
(min.)
0
0
(value of the option selected in parameter C4)
Status of COOL relay with probe fault
0=OFF; 1=ON;
0
2
2=Average based on last 24 hours prior to probe fault;
C6
Status of COOL relay with probe fault
0=OFF; 1=ON;
2=Average based on last 24 hours prior to probe fault;
0
2
3=ON-OFF as prog. C7 and C8
Time relay ON in case of faulty probe
C7
(min.)
0
10
(If C7=0 and C8¹0, the relay will always be OFF deenergised)
Time relay OFF in case of fault of probe 1
C8
(min.)
0
5
(If C8=0 y C7¹0, the relay will always be ON energised)
C9
Maximum duration of fast freezing mode. (0=off)
(h.)
0
24
Change set point (SP) in fast freezing mode, when it reaches this point
C10
(ºC / ºF)
0
-50.0 C3-SP ! !
(SP + C10) returns to normal. (SP+C10 ³ C3) (0=OFF)
Length of inactivity at digital input to activate ECO mode
C11
(h.)
0
2
(Only if P10 or P11=1) (0=OFF)
C12
Change set point (SP) in ECO mode (SP+C12
£
C2) (0=off)
(ºC / ºF)
0
2
EP
Exit to Level 1
DEFROST (If P0=0)
Description
Values Min. Def. Max.
d0
0
*
Defrost frequency (Time between two starts)
(h.)
dEF
d1
Maximum defrost duration (0=defrost deactivated)
(min.)
0
*
Type of message during defrost:
0=Currentl temperature;
d2
0
2
1=Temperature at start of defrost;2=Display dEF message
d3
Maximum duration of message (time added at the end of the defrost)
(min.)
0
5
d4
Defrost end temperature (probe 2) (If P4 ¹ 1)
(ºC / ºF)
-50.0
8.0
Defrost on equipment start-up 0=NO, First defrost as per d0,
d5
0
0
1=YES, First defrost as per d6
d6
Defrost start delay on equipment start-up
(min.)
0
0
d7
Defrost type:
0=Resistors,
1=Inverted cycle
0
0
Calculated time between defrost periods:
d8
0
0
0=Total actual time; 1 =Sum of times the compressor is on
d9
Drip time at end of defrost (compressor and fans off) (if P4 ¹ 1)
(min.)
0
1
EP
Exit to Level 1
PROGRAMMING
20"
20"
20"
Change
Change
Change
10"
parameters
Menu
value
SET
SET
SET
SET
OK
OK
Level 1
Level 2
Level 3
Menu
Parameters
Values
AKO-D1460x
AKO-D1461x
AKO-D1462x
AKO-D1463x
AKO-D1464x
FAN CONTROL (Evaporator)
Description
99.0 ! ! ! !
F0
Fan shut-down temperature as per probe 2 (if P4 ¹ 1)
FAn
150
! !
F1
Probe 2 differential (If P4 ¹ 1)
20.0 ! ! ! ! !
F2
Stop fans when stopping compressor 0=No, 1=Yes
20.0 ! ! ! !
F3
Fan status during defrost: 0=Off; 1=On
99.0 ! ! ! !
Starting delay after defrost (if F3=0)
F4
! !
Will only operate if it is higher than d9
150
C2
! ! ! !
Stop fans on opening the door 0=No, 1=Yes
F5
(Requires a digital input configured as port P10 or P11=1)
1
! ! ! !
EP
Exit to Level 1
ALARMS CONTROL
Description
120
! ! ! !
A0
Configuration of temperature alarms: 0=Relative to SP; 1=Absolute
AL
With NTC
! !
2
A1
Maximum alarm probe 1 (must be greater than SP)
With PTC
A2
Minimum alarm probe 1 (must be less than SP)
3
! !
A3
Temperature alarm delay during start-up
A4
Temperature alarm delay after completion of a defrost
120
! !
A5
Temperature alarm delay after reaching the value of A1 or A2
External alarm / Severe external alarm delay when receiving digital input
A6
! !
signal (P10 or P11=2 or 3)
120
Deactivation delay of the external alarm / Severe external alarm when the
48
! !
A7
signal of the digital input disappears (P10 or P11=2 or 3)
A8
Show warning if defrost is terminated by time-out 0=No, 1=Yes
Alarm relay polarity
0=Relay ON in alarm (OFF no alarm)
A9
24
! !
1=Relay OFF on alarm (ON with no alarm)
A10
Temperature Alarm Differential (A1 and A2)
C2-SP ! !
A12
Door open alarm delay (if P10 or P11=1)
! ! ! ! !
EP
Exit to Level 1
GENERAL STATUS
Description
96
! ! ! !
P0
Type of operation 0=Direct, Cold;1=Inverted, Heat
CnF
255
! ! ! !
P1
Delay of all functions on receiving electrical power
2
! ! ! !
Access code (password) functions
P2
0=Inactive; 1=Block access to parameters; 2=Keyboard lock
! ! ! !
255
Selection of type of inputs
99.0 ! !
P4
1=1 Probe (S1+DI1+DI2)
2=2 Probes (S1+S2+DI1+DI2)
3=3 Probes (S1+S2+S3+DI1)4=2 Probes (S1+S3+DI1)
1
! !
P5
MODBUS address (Only AKO-D146xx-C)
! !
255
Configuration of AUX relay
1=Defrost / 2nd Defrost 2=Alarm
P6
1
! !
3=Light
4=Pump down 5=Master Defrost
1
! !
Temperature display mode
0=Whole in ºC 1=One decimal in ºC
P7
2=Whole in ºF 3=One decimal in ºF
! !
255
Probe to be displayed (as per parameter P4)
! ! ! !
P8
0=visualization of all the probes in sequence;
1=Probe 1; 2=Probe 2; 3=Probe 3
P9
Selection of probe type 0=NTC; 1=PTC
Change set point
5"
SET
SET
Temperature
Current
Back up one level
SET
Indication
Value
without saving changes
SET
OK
AKO-D1460x
AKO-D1461x
AKO-D1462x
AKO-D1463x
AKO-D1464x
GENERAL STATUS
Values Min. Def. Max.
Description
(ºC / ºF)
-50.0
*
99.0 ! !
Configuring digital input 1 (DI1)
0= Off
CnF
0.1
2.0
20.0 ! !
(ºC / ºF)
2=External alarm
3=Severe external alarm
P10
4=Slave defrost
5=Act. ECO mode by pushbutton
0
1
1
! !
6=Act. Fast Freezing
7= Low pressure switch *
0
*
1
! !
8=Remote defrost
9=Act. ECO mode by switch
! !
(min.)
0
3
99
Configuring digital input 2 (DI2)
0= Off
2=External alarm
3=Severe external alarm
0
0
1
! !
P11
4=Slave defrost
5=Act. ECO mode by pushbutton
6=Act. Fast Freezing
7= Low pressure switch *
! !
8=Remote defrost
9=Act. ECO mode by switch
Digital input polarity 1
0=Energised on closed contact,
Values Min. Def. Max.
P12
1=Energised on open contact
! ! !
0
0
1
Digital input polarity 2
0=Energised on closed contact,
P13
99.0
99.0 ! ! !
1=Energised on open contact
(ºC / ºF)
A2
-
150
!
P14
Maximum start-up time after pump down
! ! !
(ºC / ºF)
-50.0 -50.0
A1
P15
Maximum pump down time
(min.)
0
0
120
! ! !
P22
Cold room light timer
! ! !
(min.)
0
0
99
EP
Exit to Level 1
(min.)
0
30
99
! ! !
ACCESS AND INFORMATION CONTROL
(min.)
0
0
120
! ! !
Description
L5
Access code (Password)
tid
! ! !
(min.)
0
0
120
PU
Program version (Information)
Pr
Program revision (Information)
0
0
1
! !
EP
Exit to Level 1
0
0
1
!
!
EP
Exit programming
! ! !
(ºC / ºF)
0.1
1.0
20
*
Only available on
AKO-D1464x / D-1464x-C.
(min.)
0
2
120
! ! !
P10/P11: Options available depending on the model.
! ! !
MESSAGES
Values Min. Def. Max.
! !
L5
Access code (Password) request
0
*
1
(min.)
0
0
255
! ! ! !
dEF
Indicates a defrost is underway. (Only if parameter d2=2)
E1/E2/E3
Probe 1 / 2 / 3 faulty (
open circuit, crossover or temperature outside the probe limits
! ! ! ! !
0
0
2
InI
Setup wizard (See section "Start-up")
AH
Flashing: maximum temperature alarm on probe 1 (A1)
! !
1
1
4
AL
Flashing: minimum temperature alarm on probe 1 (A2)
AE
External alarm activated (only if parameter P10 or P11=2)
! ! !
1
1
255
AES
Severe external alarm activated (only if parameter P10 or P11=3)
1
1
5
!
Adt
Defrost time-out alarm (only if parameter A8=1)
PAb
Door open alarm (Only if P10 or P11=1 and as per time at A12)
0
1
3
! ! ! ! !
Pd
Flashing: Pump down malfunction error (Stop).
LP
Flashing: Pump down malfunction error (Start-up).
0
1
3
! !
D: Displays the message on the display
0
0
1
! ! !
Technical specifications
Power supply
AKO-D14602 / AKO-D14610. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230 V~ ±10 % 50/60 Hz 3.5 VA
Change
value
OK
AKO-D14622 / AKO-D14632 / AKO-D14642 . . . . . . . . . . . . . . . . . 230 V~ ±10 % 50/60 Hz 3.75 VA
AKO-D14601 / AKO-D14612 / AKO-D14621 /
SET
AKO-D14631 / AKO-D14641 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 V~ +8 % - 12 % 50/60 Hz 4 VA
New
Temperature
AKO-D14622-C / AKO-D14632-C / AKO-D14642-C . . . . . . . . . . . . . . . . . 90-240 V~ 50/60 Hz 7 VA
Value
Indication
Maximum Voltage SELV circuits
Inputs
AKO-D1460x / AKO-D1461x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AKO-D1462x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
AKO-D1463x / AKO-D1464x (
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Relay COOL 16 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EN60730-1: 12(10) A 250 V~)
Relay DEF 8 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EN60730-1: 8(4) A 250 V~)
Relay FAN 16 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EN60730-1: 12(10) A 250 V~)
Relay AUX 6 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EN60730-1: 5(4) A 250 V~)
Relay ALARM 6 A (AKO-D1462x). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (EN60730-1: 5(4) A 250 V~)
Number of relay operations
Types of probe
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NTC AKO-149xx / PTC AKO-1558xx
Measurement range
Resolution
-50 to 100 ºC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0,1 ºC
> 100 ºC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 ºC
Working environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -10 to 50 ºC, humidity <90 %
Values Min. Def. Max.
Ambient storage humidity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30 to 70 ºC, humidity <90 %
1=Door contact
Class of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IP40
!
0
0
3
Fixation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wall assembly, adaptable to built-in housing
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171 x 94 x42 mm
! !
0
0
9
Connections
. . . . . . . . . . . . . . . . . . . . . . . . . . .
Rating of control device
1=Door contact
0
0
3
!
environments, Class A software and continuous operation. Pollution classification 2 s / UNE-EN 60730-1.
Double insulation between supply, secondary circuit and relay output.
0
0
9
! !
Rated pulse voltage
Temperature during ball-pressure test
0
0
1
! ! !
Accessible parts
Parts which position active elements
0
0
1
! ! !
Voltage and current as per EMC test
!
AKO-D14602 / D14610 / D14632 / D14622 / D14622-C / D14632 /
(Seg.)
0
0
120
(min.)
0
0
15
!
D14642 / D14632-C / D14642-C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207 V, 17 mA
0
0
999
!
(min.)
AKO-D14601 / AKO-D14612 / AKO-D14621 / D14631 / D14341 . . . . . . . . . . . . . . . . 105 V, 36 mA
! ! ! ! !
Current of radio jamming supression tests
Values Min. Def. Max.
0
-
99
! ! ! ! !
! ! ! ! !
-
-
! ! ! ! !
Accesories
! ! ! ! !
! ! ! ! !
D -
D -
)
D A
D -
D A
D A
D A
D A
D -
D -
D -
D -
A: Activates the alarm relay (if available).
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 V
input
NTC/PTC
input
NTC/PTC + 2
digitised inputs
According to P4
) . . . . . . . . . . . . . . . . . 2
inputs
NTC + 2
digitised inputs
inputs
NTC + 1
digitised input
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EN60730-1: 100.000
operations
NTC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50,0 ºC to +99,9 ºC (-58,0 ºF to 210 ºF)
PTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -50,0 ºC to +150 ºC (-58,0 ºF to 302 ºF)
Connections via screw terminals for cables up to 2.5 mm²
: Independent mounting,
automatic operation feature Type 1.B, for use in clean
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2500 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 ºC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 ºC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270 mA
The AKO-D14918 programming key allows you to quickly and easily copy
configured settings from one controller to another with the same functionality.
AKO-D14918