FLEETFLIX AI+ PRO Quick Start Manual - Page 2

Browse online or download pdf Quick Start Manual for Dash Cameras FLEETFLIX AI+ PRO. FLEETFLIX AI+ PRO 3 pages.

Print Page

The FleetFlix Quick Start Guide

Installing the Cables

........

Sl - Reference the vehicle's user manual to find the location of the fuse box and

OBD connector. Then check the ACC fuse specification on the box cover.

S2 - Pull out the ACC fuse.

S3 - Select the appropriate Blade Fuse Holder cable. Plug in the ACC fuse that was

removed from the fuse box into the Blade Fuse Holder cable, and then plug in the

other ACC fuse that we provided.

S4 - Plug in the Blade Fuse Holder cable into the ACC fuse slot in the fuse box.

S5 - If using LDW, gray and pink input wires will need to be connected.

S6 - Remove the right panel I/O cover.

S7 - Feed the 12-pin connector of the OBD II Power Cable through the

hole on the right panel I/O cover.

S8 - Reinstall the right panel I/O cover. Make sure to tighten the screw.

S9 - Connect the other end of the OBD II Power Cable to the Blade Fuse

Holder cable.

S10 - Plug in the OBD II Power Cable to the OBD II connector in the

vehicle.

Mounting

Sl - Attach the adhesive tape mounting bracket or optional suction cup

onto the Fleetflix Dash Cam.

S2 - Find a suitable place to install the FleetFlix Dash Cam onto the wind

shield. Use alcohol to clean the glass before mounting the device. (It is

recommended to install the device in the center of the wind shield

below the review mirror.)

Installing the Micro SD Card (As Needed)

Sl - Loosen the screw of the right panel I/O cover, remove cover.

S2 - Locate the Micro SIM Card slot.

S3 - Insert a Micro SIM card into card slot. Use your fingernail to press the

card into the slot. When fully inserted, the card will snap into the slot.

Adhesive Tape

Mounting Bracket

Plugging in the 080 II Power Cable to the 080 II connector

*The calibration process takes

about 3-5 minutes.

Note - Re-calibration is required

in case of relocating or

transferring the dashcam

to another vehicle.

www.FleetFlix.com

Wire Color Guide for OBD Harness

■

Yellow Input Ignition ACCl Connector

Gray Wire Input Dedicated Left Blinker

Pink Input Dedicated Right Blinker

■

Orange Input

Purple Input

■

Blue Input

■

Green Input

Brown Output

. . . . .

12-Pin Power Connector

2 4 6

81012

ACC Connector

O8D II Connector

FLEETFLIX

After installing the camera, the following measurements are needed

WHAT ARE THE

BENEFITS OF

• Hood length - the distance from the front lens of the camera and the front

bumper

THE FLEETFLIX

•

Vehicle width - the total width of the vehicle at its widest point in front of the

camera (typically wheel arch to wheel arch)

TECHNOLOGY?

• Camera height - the distance from the ground to the bottom of the camera

Driver position - which side of the vehicle the steering wheel is on, (left hand

is typical for American market vehicles)

The FleetFlix Al+ Pro dashcam is

packed with the latest

advancements in technology,

After install has been completed and measurements have been saved in the

offering fleets of all sizes

database, the camera will need to be calibrated. To calibrate the camera properly

a powerful device to enhance

you will need to take the vehicle on a short drive under these conditions:

driver and fleet safety,

and reduce safety-related costs.

• Good contrast for lane markers

• Capable of supporting 30+ mph for 3-5 minutes

• Avoids hills or turns

• Reasonable weather

• Light traffic

To start Calibration

While the vehicle is driving down the road in these optimal conditions, press and

hold down the driver alert button for 4 seconds. The camera will announce

"Calibration Started" and once complete camera will announce "Calibration

Done". Once calibration is complete, your camera has been successfully set up

and returning the button to driver alert. If the camera is ever removed or

unmounted, calibration will need to be completed again.

The FleetFlix Al+ Pro is fully

integrated into the Geotab

P latform ..