3M 6200 Technical Data Sheet - Page 3

Browse online or download pdf Technical Data Sheet for Respiratory Product 3M 6200. 3M 6200 3 pages. Half facepiece respirator
Also for 3M 6200: User Instructions (16 pages), Quick Start Manual (2 pages), Quick Start Manual (2 pages), Quick Start Manual (2 pages), Quick Start Manual (2 pages), User Instructions (2 pages)

Print Page

Fitting Instructions

Before assigning any respirator to be worn in a contaminated

area, we recommend that a qualitative or quantitative fit check

be performed before entering the workplace.

Fitting instructions must be followed each time the respirator is worn.

Place the respirator over the mouth and nose, then pull the

harness over the crown of the head.

Take the bottom straps in both hands, place them at the back

of the neck and hook them together.

Tighten the top straps first by pulling on ends to achieve a

comfortable and secure fit.

Tighten bottom straps using either front or rear adjustments.

(Strap tension may be decreased by pushing out on back side

of buckles).

Materials

PART

Face Mask

Head Harness

Head Strap

Inhalation Valve

Exhalation Valve

Gasket

6000 Filter Body

6000 Filter Element

5000 / 2000 Series Filter material

Fit Check

Perform a positive and/or negative pressure fit check each time

the respirator is donned.

Positive pressure Face Fit check (all Filters except 3M™

6035, 6038 / 2000 Series Filters).

Place the palm of the hand over the exhalation valve cover

and exhale gently.

If the respirator bulges slightly and no air leakage between

the face and the respirator is detected, a proper fit has been

achieved.

If air leakage is detected, reposition the respirator on the

face and/or readjust the tension of the strap to eliminate the

leakage.

Repeat the above face fit check.

If you cannot achieve a proper fit, do not enter the

contaminated area. See your supervisor.

Negative pressure face fit check (3M™ 6035, 6038 / 2000

Series Filters)

Push the filter cover down (6035, 6038) or press your thumbs

into the central indentation of the filters (2000 series), inhale

gently and hold your breath for five or ten seconds.

If the respirator collapses slightly, a proper fit has been

achieved.

If air leakage is detected, reposition the respirator on the

face and/or readjust the tension of the straps to eliminate the

leakage.

Repeat the above face fit check.

If you cannot achieve a proper fit, do not enter the

contaminated area. See your supervisor.

MATERIAL

Thermoplastic Elastomer

Polyethylene

Polyester / cotton / Polyisoprene

Polyisoprene

Silicone Rubber

Polystryrene

Activated / Treated Carbon

Polypropylene

Spare parts

PART

MATERIAL

6895

Inhalation Gasket

501

Retainer for 5000 Series Filters

603

Particulate Filter Platform

105

Face Seal Cleaner

S-200

Supplied Air Regulator

106

Half Mask Carry Case

Respiratory Protection is only effective if it is correctly

selected, fitted and worn throughout the time when the

wearer is exposed to respiratory contaminants.

3M offers advice on the selection of products, and training in the

correct fitting and usage.

For more information on 3M products and services please

call the 3M Health & Safety Helpline.

Important Notice

3M does not accept liability of any kind, be it direct or consequential (including, but not limited to, loss of profits, business and/or goodwill)

arising from reliance upon any information herein provided by 3M. The user is responsible for determining the suitability of the products

for their intended use. Nothing in this statement will be deemed to exclude or restrict 3M's liability for death or personal injury arising from

its negligence.

3M a/s

Sikkerhedsprodukter

Fabriksparken 15

DK-2600 Glostrup

Telefon: 43 48 01 00

Fax: 43 96 85 96

E-mail: [email protected]

www.3Msikkerhed.dk

Please recycle.