Clipper NORTON CDM 204 Operating Instructions Manual - Page 6

Browse online or download pdf Operating Instructions Manual for Drill Clipper NORTON CDM 204. Clipper NORTON CDM 204 9 pages.

Print Page
Overload protection
To protect the motor, operator and diamond drill, the
machine is provided with a mechanical, electronic and
thermal overload safety system. Whenever the engine is
switched off due to overload, it must be switched on again
as soon as possible to cool the engine. Then let the drill
turn for a minimum of 1 minute.
1 - Electronic / Thermal
If the machine is being overloaded, the motor electronic
switches over to the pulsating operation for showing the
operator the overload. If the force is then not reduced, the
motor switches off after a few seconds. After switching the
machine off and on again, the motor start again softly.
2 - Mechanical
If the drill bit suddenly gets stuck, the slip coupling is
activated to disconnect the main axis from the engine.
Make sure you switch off the engine immediately and
remove the drill from the hole. When the slip coupling is
activated for a longer period, the mechanical slip must be
re-tuned by a recognized expert.
Drilling with water cooling - Water connection
IF APPLICABLE
The drilling machine is equipped with a water tap, which
includes a 'Gardena' connection. Make sure that the core
drill is sufficiently cooled and that the slurry is properly
discharged. The maximum permitted water pressure is 3
bars. Always use clean water to enlarge the life span of
the internal water seals. In case of leakage, the drilling
machine has to be checked IMMEDIATELY by a certified
mechanical expert.
Dry drilling - Dust Extraction
IF APPLICABLE
For dry drilling only use designated drill bits. Dry drilling is
only possible in masonry, brick/block and sandstone.
Dust released during dry drilling is dangerous to your
health. Therefore, a dust extraction system specially
intended for this purpose must be used, and if necessary,
a dust mask worn. The use of a dust extraction system is
also required to optimize the life time of the diamond drill
bit. To prevent clogging of the dust extraction system it is
essential that the materials which are being drilled are
completely dry. Information about dust extraction systems
is available at your diamond tools supplier.
ENVIRONMENTAL PROTECTION
According to the European regulation
2002/96/EC, SAINT-GOBAIN ABRASIVES
is responsible to recycle old electric drill
motors. You are therefore requested
to return old SAINT-GOBAIN ABRASIVES electric drill
motors to your local reseller.
5
WARRANTY
Guarantee claims must be shown by submission of
purchase invoice. The guarantee includes the repair of
defects which have occurred and can be linked by to
material or manufacturing faults.
Not covered by guarantee:
• Defects or damages which have arisen due to incorrect
use or connection.
• Machine overload.
• When maintenance has been carried out incorrectly or
badly.
• Information in the manual has not been properly followed.
• The machine is used by unqualified persons.
• If the machine is used for purposes for which it is
unsuitable.
• The machine is repaired using unoriginal parts.
• If the machine encryption is damaged or deleted.
• If defects are caused by fire, damp and/or transport.
EMISSION
Typically, the A-weighted noise levels of the product are:
Sound pressure level 94 dB(A); Sound power level 105
dB(A). Uncertainty K = 3 dB.
WEAR HEARING PROTECTION!
The measured average vibration is less than 2,5 m/s².
Measured values determined according to EN 60745.
DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
(CDM 204) is in conformity with the following standards or
standardized documents:
EN 60745-1 ; EN 55014-1 ; EN 55014-2 ;
EN 61000-3-2 ; EN 610003-3 ; EN 62841-1 ;
EN 62841-2-1 ; 2011/65/EU ; 2014/30/EU ;
2006/42/EG ; 2014/130/EU
Machine Design Manager
Francois Chianese
03.01.2022
SAINT-GOBAIN ABRASIVES S.A.
190, bd. J.F. Kennedy
L-4930 BASCHARAGE, LUXEMBOURG