Cloer 7520 Instruction Manual - Page 8

Browse online or download pdf Instruction Manual for Coffee Grinder Cloer 7520. Cloer 7520 20 pages. Cloer 7520

Print Page

1. Operation

Dear Customer,

Thank you for choosing the Cloer coffee grinder.

From now on, you are able to enjoy coffee made

of freshly ground coffee beans.

We hope you enjoy your new coffee grinder.

Description

1 Grinding ring with seal

2 Number-of-cups controller

3 Start / Stop button

4 Coffee powder container with lid

5 Coffee bean container with lid

6 Degree-of-grinding controller

7 Housing with conical grinder

8 ON/OFF switch for power supply

Setting up

Remove all packaging parts and, if applicable,

stickers, not the rating label.

Place the coffee grinder on a dry, non-slip and

even surface.

Before using the first time

Please read this instruction manual attentively

before using it for the first time.

Clean the device and its accessories with a moist

cloth. ATTENTION! Sharp edges!

Let the parts dry fully before use.

Safety notices for operation

The coffee grinder is exclusively intended

to grind coffee beans. Do not fill any other

foodstuffs (other beans, nuts etc.) into the

device.

Never operate the device without beans.

The device must never be operated without the

grinding ring.

The grinding ring in turn must not be used

without the seal attached.

The appliance meets the

requirements of the applicable

EC directives.

The appliance is intended for

indoor use only.

Never leave the device unsupervised in

operation.

Never fill the container with coffee beans over

the rim (max. 300g).

Please observe that the coffee meal container

has a volume of max. 110 g.

Never use the coffee bean container and the

coffee meal container without a lid.

Take off the coffee bean container only when

it is empty, since the beans will otherwise

fall through the openings at the bottom. If

necessary, tip out the beans (fig. 1). Disconnect

the device from the mains first and remove the

coffee meal container.

(see page 2)

If the grinder does not start up properly, caught

beans may be the cause. In this case, switch to

the coarsest grinding degree „18" and try again.

Then you can return to the original grinding

degree while the device is running.

Never immerse the coffee grinder in water or

other liquids!

ATTENTION! Always unplug

appliance when not in use and

before cleaning!

Assembly

At the beginning, ensure that the device is not

yet connected to the mains and that the on/off

switch (8) is set to OFF " ".

Before assembly, ensure that the grinder is free

of old coffee beans.

Place the grinding ring incl. seal (1) into the

position on the conical grinder (below the

coffee bean container (5) ). The three teeth of

the grinding ring fit the three protrusions in the

device precisely. Caution! Sharp edges!

Place the empty coffee bean container (5) onto

the device. The triangle on the coffee bean

container must point precisely to the grey

mark of the device. Now push the coffee bean

container down and turn it clockwise in the

direction of the grinding degree marks.

Please observe that your coffee mill will not

work for reasons of safety when the coffee

bean container (5) is not properly installed.

Now place the coffee meal container with lid (4)

in the right position.

Operation

Fill coffee beans into the coffee bean container

(5) (max. 300 g).

Plug cord into a standard electrical outlet.

Choose the desired degree of grinding (6)

between 1 and 18, by turning the coffee bean

container (5).

Important: 1 is the finest grinding degree,

18 is the coarsest one. The mark

corresponds roughly to the grinding degree

of commercial coffee powder.

Please observe that the grinding degrees

controller (6) must not be adjusted during

operation.

Please observe that less powder will come

out at a fine grinding degree than a coarse

one at the same number of cups.

Now set the cup number controller (2) to the

desired number of cups. Please observe that

Fig. 1