Ashley Entertainment Spectrum Instruction Manual - Page 8

Browse online or download pdf Instruction Manual for Musical Instrument Ashley Entertainment Spectrum. Ashley Entertainment Spectrum 20 pages.

Print Page

Frequently Asked Questions

My instrument has small cracks in the finish. What causes this?

Is it covered under warranty?

This is known as "finish checking". This is a result of the instrument being subjected

to a rapid change in temperature or humidity. In most cases it happens in the winter

when a chilled instrument is exposed to warm air. The cracks are a result of the wood

expanding faster than the lacquer. Since we have no control over environmental

conditions surrounding the use of the instrument we cannot cover this type of

situation under our warranty.

What is stand damage?

Stand damage occurs when the chemicals in the rubber used on guitar stand reacts

with the finish of our instruments. Unfortunately this situation is not covered under

your warranty. The safest way to prevent this from happening is to cover

the rubber parts of your stand with a soft cotton cloth.

How do I attach the strap to the acoustic guitar?

The guitar strap provided has a hole which allows room for the strap button located

on the bottom of the guitar body. The other end of the strap has a string which ties

to the neck of the guitar at the bottom of the headstock above the nut and below the

first machine head, underneath the strings.

Where do I purchase additional instructional material, sheet music and

musical accessories for my instrument?

Please visit www.ashleyentertainmentcorp.com and you will find all our accessories

and a selection of books and instructional material available for sale.

If I have missing parts or my unit is defective within 30 days of purchase

how would I obtain assistance?

Write – Ashley Entertainment Corp.

PO Box 777944, Henderson, NV 89077

Call – 1-877-914-1800

Email – [email protected]

www.ashleyentertainmentcorp.com

Instructions For EQ/Tuner

Please read the following instructions before use :

1. Battery Installation - Open the battery compartment, insert a 9V battery and observe the +/-

polarity as indicated. Close the battery compartment.

2. Tuning and Tone accuracy indicator – After battery is installed, the tuner can be used for tuning.

Adjust the strings to a certain degree of tightness or looseness so that the tone LED indicator

will correspond to the right string and tone becomes ON.

3. Tone is accurate when Green LED is ON after adjusting the string.

4. Connection – connect the guitar cable (not provided with guitar pack) to guitar amplifier.

A. If using amplifier, earphone or other electronic equipment, you need to tune timbre and volume.

Push the switch to EQ mode and the EQ will be activated.

B. Timbre: Use audio ascension to adjust different audio outputs. Use volume knob for adjusting

the volume output.

C. Specification

EQ : 5184 4 band + tuner

Audio receiving: Piezoelectric mode

Audio output : 6.3mm outlet

Tuning Mode : MIC receiving.

Tuning Display : LED

Battery : 6F22(9V) *1

Accessory

EQ *1/Battery box*1/Pick up*1/Battery

Using Your EQ/Tuner

• 4 Band Eq And Tuner

1) Open up battery compartment and remove plastic coating from battery. Reinsert the battery.

2) There is a 3 function setting: Off/EQ/Tuner. Slide to the appropriate setting for use.

3) To tune - strum each string until the green indicator LED appears. Red LED indicates that

the string is out of tune.

4) When finished tuning each string, move selector switch to EQ

5) Adjust the bass, middle, treble settings until desired sound is achieved.

6) When finished playing, slide the function setting to the off position.

• 3 Band Eq And Tuner

1) Open up battery compartment and remove plastic coating from battery. Reinsert the

battery

2) The Red Power Button has a double push function. One push turns on the tuner, a second push

turns on the EQ.

3) Press the power button once and the tuning indicator LED will come on for a brief moment. It

will then blink slowly to show the EQ is in tuning mode.

4) To tune - strum each string until the green

indicator LED appears. Red LED indicates that

the string is out of tune.

5) When finished tuning each string, push the

power button again to move into EQ mode.

The flashing green LED will stop, indicating

that the EQ function is in operation.

6) Adjust the bass, middle, treble settings

until desired sound is achieved.

Note:

If EQ is not in use, it is recommended

to take out the battery in order to avoid

any possible damage on the tuner due

to leakage of battery.

NOTE: If there is no sound be sure to

check that the volume is up on both the

EQ and your Amp. To extend the life of

the battery it is recommended to remove

it when guitar is not in use.