Cypress Semiconductor STK14C88-3 Specification Sheet - Page 6

Browse online or download pdf Specification Sheet for Computer Hardware Cypress Semiconductor STK14C88-3. Cypress Semiconductor STK14C88-3 18 pages. 256 kbit (32k x 8) autostore nvsram

Print Page

Best Practices

nvSRAM products have been used effectively for over 15
years. While ease-of-use is one of the product's main system
values, experience gained working with hundreds of applica-
tions has resulted in the following suggestions as best
practices:
■
The nonvolatile cells in an nvSRAM are programmed on the
test floor during final test and quality assurance. Incoming
inspection routines at customer or contract manufacturer's
sites, sometimes, reprogram these values. Final NV patterns
are typically repeating patterns of AA, 55, 00, FF, A5, or 5A.
End product's firmware should not assume an NV array is in
a set programmed state. Routines that check memory
content values to determine first time system configuration
and cold or warm boot status, should always program a
unique NV pattern (for example, a complex 4-byte pattern of
46 E6 49 53 hex or more random bytes) as part of the final
Table 2. Hardware Mode Selection
CE
WE
H
X
L
H
L
L
X
X
L
H
L
H
Notes
1. I/O state assumes OE < V
. Activation of nonvolatile cycles does not depend on state of OE.
IL
2. HSB STORE operation occurs only if an SRAM WRITE has been done since the last nonvolatile cycle. After the STORE (if any) completes, the part will go
into standby mode, inhibiting all operations until HSB rises.
3. CE and OE LOW and WE HIGH for output behavior.
4. The six consecutive addresses must be in the order listed. WE must be high during all six consecutive CE controlled cycles to enable a nonvolatile cycle.
5. While there are 15 addresses on the STK14C88-3, only the lower 14 are used to control software modes.
Document Number: 001-50592 Rev. **
system manufacturing test to ensure these system routines
work consistently. Power up boot firmware routines should
rewrite the nvSRAM into the desired state. While the
nvSRAM is shipped in a preset state, best practice is to again
rewrite the nvSRAM into the desired state as a safeguard
against events that might flip the bit inadvertently (program
bugs or incoming inspection routines).
■
The V
minimum and a maximum value size. Best practice is to meet
this requirement and not exceed the max V
because the higher inrush currents may reduce the reliability
of the internal pass transistor. Customers who want to use a
larger V
should discuss their V
understand any impact on the V
of a t
A
– A
HSB
13
0
H
X
H
X
H
X
L
X
H
0x0E38
0x31C7
0x03E0
0x3C1F
0x303F
0x0FC0
H
0x0E38
0x31C7
0x03E0
0x3C1F
0x303F
0x0C63
Nonvolatile RECALL
value specified in this data sheet includes a
CAP
value to ensure there is extra store charge
CAP
size selection with Cypress to
CAP
CAP
period.
RECALL
Mode
IO
Not Selected
Output High Z
Read SRAM
Output Data
Write SRAM
Input Data
Nonvolatile Store
Output High Z
Read SRAM
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Nonvolatile STORE
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Read SRAM
Output Data
Output Data
STK14C88-3
value
CAP
voltage level at the end
Power
Standby
[1]
Active
Active
[2]
I
CC2
[1, 3, 4, 5]
Active
[1, 3, 4, 5]
Active
Page 6 of 17
[+] Feedback