Asko D3122 Installation Instructions Manual - Page 10

Browse online or download pdf Installation Instructions Manual for Dishwasher Asko D3122. Asko D3122 12 pages. D3122 use & care guide fr (french ucg 2+1 warranty)
Also for Asko D3122: Use And Care Manual (16 pages), Quick Start Manual (2 pages), (Spanish) Uso Y Cuidado (16 pages), (French) Manuel D'utilisation (16 pages)

Print Page
Asko D3122 Installation Instructions Manual
FITTING THE
FITTING THE
FITTING THE D3252XLFI, D3532XLFI AND D3532XLFIWS
FITTING THE
FITTING THE
CUST
CUST
OM DOOR
OM DOOR P P P P PANEL
OM DOOR
CUST
CUSTOM DOOR
CUST
OM DOOR
The D3252XLFI, D3532XLFI, and D3532XLFIWS can
only be installed with a fully-integrated custom door
panel that extends from the toe kick to the counter top.
The unit comes with everything needed to make
installing the door panel easy. The door is predrilled for
the panel's mounting screws.
CUSTOM P
CUST
CUST
OM P
OM P
OM PANEL DIMENSIONS
ANEL DIMENSIONS
ANEL DIMENSIONS
ANEL DIMENSIONS
CUST
CUST
OM P
ANEL DIMENSIONS
Width:
23-1/2" (597 mm)
Height:
30 1/8" (765 mm)
(Measured from the top of the panel to the lower edge of
the kitchen cabinet.)
Thickness:
3/4" (19 mm) max
Weight:
Up to 22 lb.
Fit the handle onto the panel according to the manufacturer's instructions.
(NOTE: A handle should be used rather than a knob, because a knob
does not provide enough grip.)
NOTE: Before fitting the custom panel, the dishwasher must be installed
underneath the cabinet. After you've made the required measurements,
pull the machine out again to install the panel.
NOTE: Specifications subject to change without notice.
PREP
PREP
PREP
PREP
PREPARING
ARING THE
ARING
ARING
ARING
THE
THE
THE W W W W W OOD P
THE
1.
Lay the template edge-to-edge with the lower edge of the dishwasher
door or the adjusting frame. The broken line on the template must
pass through the center of the keyholes on the door.
2.
Using a pen or screw, punch holes in the template where the
keyholes are.
3.
Lay the template on the back of the wood panel, edge-to-edge with
the rear of the lower edge and the left edge of the panel.
4.
Mark the location of the hole on the panel.
5.
Turn the template over and lay it on the right side of the wood panel
and mark the location of the second hole.
6.
Screw the short screws into the markings on the wood panel, letting
them project by about 1/16".
.
Page 10
D3252XLFI, D3532XLFI AND D3532XLFIWS
D3252XLFI, D3532XLFI AND D3532XLFIWS
D3252XLFI, D3532XLFI AND D3532XLFIWS
D3252XLFI, D3532XLFI AND D3532XLFIWS
ANEL
ANEL
ANEL
ANEL
OOD PANEL FOR MOUNTING
OOD P
OOD P
OOD P
ANEL FOR MOUNTING
ANEL FOR MOUNTING
ANEL FOR MOUNTING
ANEL FOR MOUNTING
ITEMS PRO O O O O VIDED
ITEMS PR
ITEMS PR
VIDED
VIDED
ITEMS PR
ITEMS PR
VIDED WITH
VIDED
UNIT
UNIT
UNIT
UNIT
UNIT
♦
Two 3/8" screws
♦
Four 1-3/4" screws
WITH
WITH
THE
THE
WITH
WITH THE
THE
THE