Asko D3251 Installation Instructions Manual - Page 10

Browse online or download pdf Installation Instructions Manual for Dishwasher Asko D3251. Asko D3251 13 pages. User manual d3251 use & care guide fr (french ucg 2+1 warranty)
Also for Asko D3251: Use And Care Manual (16 pages), Quick Start Manual (2 pages), Use And Care Manual (16 pages), (Spanish) Uso Y Cuidado (16 pages), (French) Manuel D'utilisation (16 pages)

Print Page

Asko D3251 Installation Instructions Manual

FITTING CUST

FITTING CUSTOM DOOR

FITTING CUST

Some models can only be installed with a fully-

integrated custom door panel that extends from the toe

kick to the counter top. The unit comes with everything

needed to make installing the door panel easy. The

door is predrilled for the panel's mounting screws.

The custom panel can be a minimum of 1/4" (6 mm)

thickness to a maximum of 3/4" (19 mm) thickness.

ITEMS PR

ITEMS PRO O O O O VIDED

VIDED

VIDED WITH

VIDED

♦

Two 3/8" screws

♦

Four 1-3/4" screws

INST

ALLING

THE CUST

INST

INSTALLING

INST

ALLING

ALLING THE CUST

THE CUST

THE CUSTOM P

Before fitting the custom panel, the dishwasher must

be installed underneath the cabinet. After you've made

the required measurements, pull the machine out again

to install the panel.

Refer to the illustration at right for instruction references.

1. Fit the handle (A) onto the panel according to the

manufacturer's instructions. (NOTE: A handle should

be used rather than a knob, because a knob does

not provide enough grip.)

2. Loosen the screws (D) on the outer edges of the

dishwasher door.

3. Pull the turbo fan exhaust frame (E) down until the

lower edge aligns with the lower edge of the cabinets

and tighten the screws.

WARNING!

The custom panel must not obstruct the turbo fan

exhaust. See step 4 above for instructions on how to

adjust the fan exhaust.

4. The two short screws (B) go into

the back of the panel, 16-3/16"

(411 mm) from the upper edge of

the panel and 5/8" (16 mm) from

the outer edges. Insert the short

screws into the panel, leaving 1/8" (3 mm) of space

between the screw head and the panel.

5. Hook the panel screws (F) into the keyholes (C) on

the dishwasher door.

6. Push the panel sidewards.

NOTE: The custom panel should not extend more

than 2-15/16" (75 mm) below the bottom of the

dishwasher door. Otherwise, it will strike the toe

kick and damage the machine and/or the panel.

7. Open the door and tighten the screws (F) inside.

8. Remove the backing from the protective tape and

affix it on the bottom edge of the panel, in front of the

exhaust vent.

9. Before you push the dishwasher into the cabinet

Page 10

OM DOOR

OM DOOR P P P P PANEL

OM DOOR

ANEL

OM DOOR

ANEL

WITH

WITH THE UNIT

WITH

THE UNIT

OM P

OM PANEL

OM P

CUST

CUSTOM P

CUST

OM P

OM PANEL DIMENSIONS

OM P

Width:

Height:

Thickness:

Weight:

NOTE: Specifications subject to change without

notice.

NOTE: Heavy-duty door springs can be purchased for

wooden door panels weighing over twelve

pounds. (P/N 8071323-77).

ANEL

opening, test the door to make sure it opens properly.

The door is counter-balanced, so it should remain

in any position. If it doesn't, you may need to adjust

the door springs (see above).

10. Fasten the diswasher to the cabinet (see page 9).

ADJUSTING THE DOOR SPRINGS

After you install the custom

panel, make sure the door

stays in place at any angle. If

it tends to fall down, pull out

the machine and tension the

door springs on the sides of

the machine by moving them

one hole farther back or by

twisting the spring to make it

shorter. If that doesn't resolve the problem, you may

need to purchase the heavy-duty door springs (part

number 8071323-77).

ANEL DIMENSIONS

23-1/2" (597 mm)

28-1/8"–30-1/8" (714 mm–765 mm)

(Measured from the top of the panel to

the lower edge of the kitchen cabinet.)

1/4" (6 mm) to 3/4" (19 mm) max

Up to 22 lb.