Asko D3331 Use And Care Manual - Page 8

Browse online or download pdf Use And Care Manual for Dishwasher Asko D3331. Asko D3331 16 pages. Use & care guide asko d3331 fr
Also for Asko D3331: Quick Start Manual (2 pages), (Spanish) Uso Y Cuidado (16 pages), (French) Manuel D'utilisation (16 pages)

Print Page

DISPLAY Y Y Y Y WINDO

DISPLA

WINDO

WINDOW W W W W

After you press Start/Stop, the display window shows

the time it took the program to run last time. (The first

time you run a program, a 1 will display.) As the program

progresses, the time remaining displays. If the time

exceeds an hour, the display alternates between the hour

and minutes remaining. The hour is designated by an h,

e.g., 1h).

If you select Delayed Start, the window will display the

number of hours selected. It will then display the count-

down time until the program starts.

The window also displays fault codes. See below.

INTERR

UPTING

INTERR

INTERRUPTING

INTERR

UPTING A PR

UPTING

ADD AN ITEM

If you want to interrupt a program to add an item, open

the door slightly until the spray arms stop turning. You

can then open the door fully and place the item into the

dishwasher. Close the door securely. The program will

continue from where it was interrupted.

WARNING! Be extremely careful when opening the

door during a program. The water is hot and you

could get scalded.

CHANGING OR ST

CHANGING OR STOPPING

CHANGING OR ST

PROGRAM

OGRAM

If you decide to change the program after you have started

the machine, press the Start/Stop button for three

seconds. You will have to select the program and options

again when you are ready to restart the program. (Note:

If the program has already gone through the wash cycle,

you will have to add detergent.)

F F F F F A A A A A UL

T CODES

ULT CODES

T CODES

In the event that the machine should fail during a

program, the display window will show a fault code. The

table below defines these codes and gives possible

causes and solutions. See also "Troubleshooting" on

page 12.

Display

Page 8

A PR

OGRAM

OGRAM T T T T T O O O O O

A PROGRAM

A PR

OGRAM

OPPING

OPPING A A A A A

OPPING

Type of Fault and Recommended Action

Too much water has entered the dishwasher. Call a service technician.

Water inlet fault. Make sure the water supply is open.

Valve leakage. Shut off the water supply and contact a service technician.

The drain is blocked. See "Troubleshooting" on page 12.

The filter is clogged. See "Cleaning the Filters" on page 9.

PROGRAM TIMES

The program times may not always be the same because

of variations in the household hot water temperature.

The dishwasher heats the water to the proper

temperature for the program selected; so if the

temperature of the water entering the dishwasher is too

low, the dishwasher will run longer because it takes

longer to heat the water. Raising your water heater

setting could help to shorten the cycle times.

A A A A A CTIV

CTIV

CTIVA A A A A TING

CTIV

TING

TING THE CHILD-SAFE

THE CHILD-SAFE

CTIV

TING

THE CHILD-SAFE

B B B B B UTT

UTT

UTTON FEA

UTT

ON FEATURE

ON FEA

TURE

As a safety measure, Model D3331 can be programmed

not to start unless the Temperature and Drying buttons

are held down simultaneously. To program this feature,

follow the steps below:

1. Turn off the power to the machine.

2. Simultaneously press and hold down the

Temperature and Drying buttons as you turn on the

power to the machine. The Temperature, Drying and

Start buttons will flash.

3. Release the buttons.

4. Press the Program button until the display shows 1

with a key symbol alongside it.

5. Press Start to confirm selection and return to main

menu.

To deactivate the button lock, simultaneously press the

Temperature and Dry buttons. You can then select the

program and options and press Start to start the unit.

The lock will reactivate automatically in three minutes.

To permanently deactivate the button lock, repeat these

steps. When the display shows 0 and key symbol goes

out, the button lock has been deactivated.

If you have corrected the fault, turn the main power off

then back on to remove the fault indication. If it still

displays, try again to correct the problem or call a service

technician.