AMC 2100 Instructies voor installatie en gebruik - Pagina 2
Blader online of download pdf Instructies voor installatie en gebruik voor {categorie_naam} AMC 2100. AMC 2100 4 pagina's. Stereo power amplifier
Ook voor AMC 2100: Servicehandleiding (15 pagina's)
Pagina afdrukken
.'
SAFETY INSTRUCTION
1.
READ INSTRUCTIONS
Allthe safety and operating instructions should be read before the
appliance is operated.
2. RETAININSTRUCTIONS
The safety and operating instructions should be retained for future
reference.
3. HEEDWARNINGS
All warnings on the appliance and in the operating instructions
should be adhered to.
4. FOllOW INSTRUCTIONS
Alloperating and use instructions should be followed.
5. WATER ANDMOISTURE
The appliance should not be used near water- for example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or
near a swimmingpool, etc.
6. CARTSANDSTANDS
The appliance should be used only with a cart or stand that is
recommended by the manufacturer.
6A.
An appliance and cart combination
should be moved withcare. Quickstops,
excessive force, and uneven surfaces
may cause the appliance and cart
combinationto overturn.
_"k'~' . -
.
7. WALL OR CEILINGMOUNTING
This equipment is not designed for use mounted on a wall or a
ceiling.
8. VENTILATION
Theappliance should be situated so that its location or position does
not interferewith its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or similarsurface that may
block the ventilation openings; or placed in a built-in installation,
such as bookcase or cabinet that may impede the flowof air through
the ventilationopenings.
9.HEAT
.
The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including
amplifiers)that produce heat.
10. POWERSOURCES
The appliance should be connected to a power supply only of the
type described in the operating instructions or as marked on the
appliance.
11. POWER-CORDPROTECTION
Power-supplycords should be routed so that they are not likelyto be
walkedon or pinched by items placed upon or againstthem, paying
particularattention to cords at plugs, comvenienee receptacles, and
the point where they exit from the appliance.
12. CLEANING
The appliance should be cleaned only as recommended by the
manufacturer.
1~. NON USE PERIODS
The power cord of the appliance should be unplugged from the outlet
when left unused for a long period of time.
14. OBJECT AND LIQUID ENTRY
Care should be taken so that objects do not fall and liquids are not
spilled into the enclosure through openings.
2..
15. SERVICING
The user should not attempt to service the appliance beyond that
described in the operating instructions. Allother servicing should be
referred to qualified service personnel.
16. DAMAGEREQUIRINGSERVICE
The appliance should be ~rviced by qualified service personnel
when:
a) The power-supply cord or the pluQnas been damaged; or
b) Objects have fallen, or liquid has been spilled into the appliance;
or
c) The appliance has been exposed to rain; or
d) The appliance does not appear to operate normally or exhibits a
marked change in performance; or
e) The appliance has been dropped, or the enclosure damaged.
17. POWER LINES.
(APPLIESTO TUNERAND RECEIVERSONLY)
An outdoor antenna should be located away Irom pow~r IiMIi.
18. OUTDOORANTENNAGROUNDING
(APPLIESTO TUNERANDRECEIVERSONLY)
If an outside antenna is connected to the receiver, be sure the
antenna system is grounded sO as to provide some protection
against voltage surges and built up static charges.
Section 810 ofthe National ElectricalCode, ANSI/NFPA No.70-1984,
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wireto an antenna
discharge
unit, size of grounding
conductors,
location of
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode. See Figure.
a) Use No. 10 AWG (5.3 mm~ copper, No. 8 AWG (8.4mm1
aluminum, No. 17 AWG (1.Omm~ copper-clad steel or bronze
wire, or larger, as a ground wire.
b) Secure antenna lead-in and ground wires to house with stand-off
insulators spaced from 4-6 feet (1.22-1.83 m) apart.
c) Mountantenna discharge unitas close as possible to where lead-in
enters house.
d) Use jumper wire not smaller than No.6 AWG(13.3 mm2) copper,
or the equivalent, when a separate antenna-grounding electrode
is used. See NECSection810-210).
.
Antenna
Grounding
According
to
the National
Electrical Code
Anlonna
D.scha'90
Unn (NEC-
Sec',on 8 '0 201
~
Elec"ic
Se,v.ce
EQu.pmen.
Groundon9 Conduc'ors.
(NEC- Sec'.on 810.211
::
Powe' Se,voce G,oundor'lI
EleCtrode System
(NEC- A.. 250 Pa.. HI
-Nahon.'
Elec'"cal Code
Avadab'e from bob,a,v. book
SlO'es. 0' Net.ona' F"e Pror"chon
Assoc..hon
(Oatterymarch Park.
Ouoncy MA 022691
~
~.