AMC CVT3030 Handleiding voor installatie en gebruik - Pagina 9
Blader online of download pdf Handleiding voor installatie en gebruik voor {categorie_naam} AMC CVT3030. AMC CVT3030 11 pagina's. Valve amplifier
Ook voor AMC CVT3030: Servicehandleiding (16 pagina's)
Pagina afdrukken
SAFETY INSTRUCTION
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the
appliance is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future
reference.
3. HEED WARNINGS
All warnings on the appliance and in the operating instructions
should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. WATER AND MOISTURE
The appliance should not be used near water- for example, near a
bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or
near a swimming pool, etc.
6. CARTS AND STANDS
The appliance should be used only with a
cart
or stand that is
recommended by the manufacturer.
6A.
An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the appliance and cart
combination to overturn.
7. WALL OR CEILING MOUNTING
This equipment is not designed for use mounted on a wall or a
ceiling.
8. VENTILATION
The appliance should be situated so that its location or position does
not interfere with its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or similar surface that may
block the ventilation openings; or placed in a built-in installation,
such as bookcase or cabinet that may impede the flow of air through
the ventilation openings.
9. HEAT
The appliance should be situated away from heat sources such as
radiators, heat registers, stoves, or other appliances (including
amplifiers) that produce heat.
10. POWER SOURCES
The appliance should be connected to apower supply only of the
type described in the operating instructions or as marked on the
appliance.
11. POWER-CORD PROTECTION
Power -supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, comvenience receptacles, and
the point where they exit from the appliance.
12. CLEANING
The appliance should be cleaned only as recommended by the
manufacturer.
13. NON USE PERIODS
The power cord of the appliance should be unplugged from the outlet
when left unused for a long period of time.
14. OBJECT AND LIQUID ENTRY
Care should be taken so that objects do not fall and liquids are not
spilled into the enclosure through openings.
15. SERVICING
The user should not attempt to service the appliance beyond that
described in the operating instructions. All other servicing should be
referred to qualified service personnel.
16. DAMAGE REQUIRING SERVICE
The appliance should be serviced by qualified service personnel
when:
a) The power-supply cord or the plug has been damaged; or
b) Objects have fallen, or liquid has been spilled into the appliance;
or
c) The appliance has been exposed to rain; or
d) The appliance does not appear to operate normally or exhibits a
marked change in performance; or
e) The appliance has been dropped, or the enclosure damaged.
17. POWER LlNES
(APPLIES TO TUNER AND RECEIVERS ONL Y)
An outdoor antenna should be located away from power lines.
18. OUTDOOR ANTEN NA GROUNDING
(APPLIES TO TUNER AND RECEIVERS ONL Y)
H an outside anten na is connected to the receiver, be sure the
anten na system is grounded so as to provide some protection
against vottage surges and built up static charges.
Section
810 cf the National Electrical Code, ANSI/NFPA No. 70-1984,
provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
See
Figure.
a) Use No. 10 AWG
(5.3 mm~
copper,
No.
8 AWG (8.4mm
2
)
aluminum, No. 17 AWG (1.0mm~ copper-clad steel or bronze
wire, or larger, as a ground wire.
b) Secure antenna lead-in and ground wires to house with stand-off
insulators spaced from
4-6
feet (1.22-1.83 m) apart.
c) Mount anten na discharge unit as close as possible to where lead-in
enters house.
d) Use jumper wire not smaller than No.
6
AWG (13.3 mm
2
)
copper,
or the equivalent, whena separate antenna-grounding electrode
is used. See NEC Section 810-210).
Antenna Grounding According to
the National Electrical Code
Ground
Clamp
Electric
Service
Equlpment
~Natlonal
Electncal Code
Avallable fram
Llbrary,
book
stores, cr National Fire
Protecllon
Associatlon (Batterymarch Park.
Quincy. MA 02269)
Antenna
DIscharge
Unlt
(~EC
Secllon 810 201
Groondmg ConduClors
INEC- SecI.on 810-21)
~Power
Service Groundlng
-
Beetrode System
(NEC'"" A,. 250 Pa,. H)