American Standard 1660.431 Installatie-instructies - Pagina 2

Blader online of download pdf Installatie-instructies voor {categorie_naam} American Standard 1660.431. American Standard 1660.431 2 pagina's. Shower systems two way or three way in-wall diverter

Pagina afdrukken

ROUGHING-IN

See Roughing-in Drawing on reverse side. The port with the BATH TUB picture is the high flow.

The DIVERTER can be installed with the inlet rotated in any position.

Supply connections are 1/2" NPT connections.

For proper positioning the finished wall must be within side of PLASTER GUARD.

Connect water to valve. The reverse side of the body is marked with arrows.

CAUTION: Do not solder near the VALVE. Damage to the SEAL may occur.

Do not seal any outlets. The DIVERTER cannot be used as a stop valve.

For support use pipe braces secured to wooden braces.

TEST DIVERTER

Check that the DIVERTER operates correctly and does not leak.

To do this, screw off the PLASTER GUARD, turn around, and

insert using the fluted pin into the fluting on the DIVERTER SPINDLE

and use as a diverter knob. Screw the PLASTER GUARD back on.

Have the wall tiled only with the PLASTER GUARD screwed on.

INSTALL TRIM

(For 1660.200/.300, handles are

purchased separately.)

When finished tiling wall, remove

PLASTER GUARD.

Place ESCUTCHEON on ESCUTCHEON

HOLDER and screw HOLDER onto VALVE.

For 1660.430/.440 Series:

Push HANDLE ADAPTER onto STEM.

Make sure arrow is up.

Assemble HANDLE and DECORATOR RING onto

HANDLE ADAPTER. Secure with HANDLE SCREW.

Snap on HANDLE CAP.

Check for leaks.

To operate, turn the HANDLE clockwise or counter clockwise.

For 1660.431/.441 Series:

Assemble HANDLE SKIRT then HANDLE LEVER to ESCUTCHEON NUT STEM. Secure

with HANDLE SCREW.

Push on INDEX BUTTON or screw on VANDAL RESISTANT INDEX CAP.

Check for leaks.

To operate, turn the HANDLE clockwise or counter clockwise.

SERVICE

To Replace O-Rings:

Turn off water supply.

For 1660.430/.440 Series:

Use a small screw driver to

remove HANDLE CAP.

Remove HANDLE SCREW, DECORATOR

RING, HANDLE and ADAPTER.

Unscrew ESCUTCHEON HOLDER and

remove HOLDER and ESCUTCHEON.

Unscrew CAP and remove STEM,

SPRING and SEALS.

Remove old DIVERTER elements and

install new parts.

Replace remaining parts in reverse order.

For 1660.431/.441 Series:

Remove INDEX BUTTON (or unscrew VANDAL RESISTANT INDEX CAP).

Remove HANDLE SCREW, LEVER HANDLE and HANDLE SKIRT.

HOTLINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time

IN CANADA 1-800-387-0369 (TORONTO 1-416-536-5609)

CAUTION

Turn off hot and cold water supplies before beginning.

DIVERTER

ESCUTCHEON

NUT STEM

ESCUTCHEON

HANDLE

SKIRT

DISK

O-RING

DISK

UPPER

O-RING

DISK

LOWER

DISK

Unscrew ESCUTCHEON HOLDER and remove HOLDER

and ESCUTCHEON.

Unscrew CAP and remove STEM, SPRING and SEALS.

Remove old DIVERTER elements and install new parts.

Replace remaining parts in reverse order.

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

PLASTER

GUARD

DIVERTER

SPINDLE

HANDLE

ADAPTER

DECORATOR

RING

INDEX

BUTTON

VANDAL-RESISTANT

HANDLE

SCREW

VANDAL-RESISTANT

HANDLE SCREW

SHAFT

SPRING

WASHER

HANDLE

SCREW

CAP

INDEX CAP

SHAFT

O-RING

CAP

5 0 3 2 1 B