14POINT7 Spartan 3 Lite Handmatig - Pagina 4

Blader online of download pdf Handmatig voor {categorie_naam} 14POINT7 Spartan 3 Lite. 14POINT7 Spartan 3 Lite 4 pagina's. 52mm

Manual - 52mm Edge AFR + Spartan 3 Lite
Gauge Mode Configuration (Continued)...
To change the Wideband display configuration of the JRP 52mm AFR gauge you will need to enter the top configuration menu. To do
this, simply press and hold the button on the back of the gauge or the remote button while live data is displayed. After 5 Seconds you
should hear an audible "Beep." Then with a short press you will navigate through the three "AF" options displayed above. Once
you've selected the wideband Air Fuel mode required for your application, wait for live data to return to the display. Your settings will
now be saved.
**Note to use the Diesel readout on these gauges, you must be using a wideband controller that has had the "0-5v analog out" Pro-
grammed to scale 10 - 40 AFR, example the "Spartan 3D."
*CAUTION* When ordering a replacement Wideband O2 Sensor: Its important to order the same type as the original. Spartan 3D/ lite
are pre-configured to operate with the sensor type they're supplied with: Eg. Spartan 3D/ Lite supplied with a Bosch is not compatible
with an ADV replacement sensor. A Spartan supplied with an ADV type is not compatible with a Bosch replacement
Detailed Button Operation
The table below shows what to expect when navigating your 52mm Edge series Air Fuel Ratio gauge, this is more or less an on the
fly cheat sheet to assist you during setup. Best way to understand all the features and functions is to read this whole instruction
manual carefully.
For further assistance/ trouble shooting please visit our YouTube channel:
Visit our social platforms for new ideas, and to see our latest products:
Alternatively send us a cheeky Dm, were here to help!
Long Press
LONG PRESS
/
GAUGE MODE
CONFIGURATION
Short Press
SHORT PRESS
COLOUR
SELECTION
Short Press
SHORT PRESS
SCREEN
BRIGHTNESS
Short Press
SHORT PRESS
OPEN/ CLOSE
CEREMONIES
SCALE INDICATOR
Spartan LED: Red slow flash, sensor too cold. Red solid light, Ok. Red fast flash, too hot. Note: If LED is green the device is attempting to
enter the boot loader mode, you need to check your wiring. This is only possible when Spartan is wired incorrectly.
Terminal 5 (Simulated Narrow band signal): Factory default is simulated narrowband output with a switch point of 1[Lambda].
Output is an RC filtered 8 bit PWM signal.
Terminal 6 (Wideband signal) The Spartan 3 Lite has a "0v to 5v" analog output signal, 0[v] @ 0.68 [Lambda] Linear to 5[v] @ 1.36
[Lambda], which equates to 10 to 20 AFR. Output is a 12 Bit DAC with a 0.1% voltage reference. If this terminal is to be shared
between a gauge and ecu / datalogger ensure same gauge wire is used, and wire length as short as possible to avoid
signal degradation.
14point7 warrants Spartan 3 Lite to be free from defects for 2 years, JRP warrants 52mm Gauge for 12 months, sensors are
consumable, and may not be warranted after use. Record the date of purchase here for warranty purposes
_______________________________________________________________________________
Notes:
JRP Edge Digital Gauge - AFR + Spartan 3 Lite Manual
See gauge mode configuration for in-depth
explanation on page 3. Hint: as you change
"Symbols blinking"
each AF# value, the outer scale will show
display style.
There are two modes for all gauges, night
LONG PRESS
Long Press
and day mode. Different colours can be set
for each mode: Red, Green, Blue, Yellow,
Purple, Snow, Mustard,
Pink, Light Blue, Orange, Teal, Off, (RGB).
There are different brightness settings
LONG PRESS
Long Press
available to match other instruments in your
vehicle. Night and day mode can be set to
different levels for each mode.
There are 3 options for the opening
LONG PRESS
Long Press
ceremony, wait for change to be saved and
view while turning gauge on/ off.
There are 3 different indicator display types.
LONG PRESS
It's best to view these options when the
vehicle is running.
Spartan Signal Output Information
CLICK ICONS TO FOLLOW LINKS
SHORT PRESS
AF1
AF3
Wait 5 sec to save
SHORT PRESS
Short Press
Day Mode
Short Press
SHORT PRESS
Night Mode
Wait 5 sec to save
SHORT PRESS
Short Press
br0
br1
Day Mode
Short Press
SHORT PRESS
br3
br4
Night Mode
Wait 5 sec to save
Short Press
SHORT PRESS
AC1
AC2
Types
Wait 5 sec to save
SHORT PRESS
so1
so2
Get help from JRP
____________.
.
AF2
br2
br5
AC3
so3
?
Page 4 of 4