American Standard Scala Corner 2664.218 Specificatieblad - Pagina 2
Blader online of download pdf Specificatieblad voor {categorie_naam} American Standard Scala Corner 2664.218. American Standard Scala Corner 2664.218 2 pagina's. Whirlpool & bathing pool high gloss acrylic
Ook voor American Standard Scala Corner 2664.218: Onderdelen (1 pagina's), Onderdelenlijst (1 pagina's), Specificatieblad (2 pagina's)
Pagina afdrukken
552mm
(21-3/4)
216mm
(8-1/2)
19mm(3/4)
CUTOUT DIMENSION
C L
OF DRAIN OUTLET
13mm (1/2)
38mm
INTEGRAL
(1-1/2)
TILE FLANGE
LEVELING
STRINGER
(NOT FOR
SUPPORT)
60mm
(2-3/8)
124mm
4-7/8
GENERAL SPECIFICATIONS FOR 2664 WHIRLPOOL
60 x 60 x 19-3/4 In. (1524 x 1524 x 502mm)
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
WHIRLPOOL MIN. OPERATING VOL.
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
(PROJECTED AREA)
PTS.
CUBE (FT
)
3
WHIRLPOOL ELECTRICAL SPECIFICATIONS
SYSTEM I PUMP
NOTES:
BATH CAN BE INSTALLED EITHER ABOVE OR BELOW FLOOR LINE AS PIER, ISLAND, OR PENINSULA TYPE INSTALLATION. SUMP OF
BATH IS SUPPORTED BY INTEGRAL FEET. NO ADDITIONAL SUPPORT REQUIRED. ENCLOSING MATERIAL BY OTHERS.
■
REFER TO INSTALLATION INSTRUCTIONS SUPPLIED WITH WHIRLPOOL FOR ADDITIONAL INFORMATION.
CONCEALED PIPING NOT INCLUDED.
FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.
●
IF INSTALLING A DECK-MOUNTED FITTING, BEFORE DRILLING ANY HOLES: CHECK FOR INTERFERENCE WITH CIRCULATING
SYSTEM PIPING, DRAIN OVERFLOW, AND APRON INSTALLATION. MOUNTING HOLES DRILLED BY INSTALLER.
PROVIDE SUITABLE REINFORCEMENT FOR ALL SUPPORTS.
IMPORTANT: Dimensions of fixtures are nominal and may vary within the range of tolerances established by ANSI Standard Z124.1. These
measurements are subject to change or cancellation. No responsibility is assumed for use of superseded or voided pages.
© 2008 AS America Inc.
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
ON/OFF
406mm
SWITCH
(16)
PROVIDE ACCESS
1041mm
FOR SERVICING
(41)
PUMP & CONTROLS
95mm
(3-3/4)
ROUGH
FLOOR
INTEGRAL
1-1/2" N.P.T.M. THREADS
FEET
1-1/2" O.D. TAILPIECE
SUPPORT
114 Lbs. ( 51 Kg.)
781 Lbs. (351 Kg.)
80 Gal. (303 L)
58 Gal. (220 L)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
14 In. (356mm)
37 Lbs./Sq.Ft. (182 Kgs./Sq.m)
1.25 HP, 9.9 AMPS,120V.
WHIRLPOOL AND BATHING POOL
552mm
(21-3/4)
216mm
(8-1/2)
19mm(3/4)
CUTOUT DIMENSION
C L
OF DRAIN OUTLET
38mm
13mm (1/2) INTEGRAL
(1-1/2)
TILE FLANGE
LEVELING
464mm
STRINGER
18-1/4
(NOT FOR
502mm
SUPPORT)
(19-3/4)
124mm
GENERAL SPECIFICATIONS FOR 2664 BATHING POOL
INSTALLED SIZE
WEIGHT
WEIGHT w/WATER
GAL. TO OVERFLOW
BATHING WELL AT SUMP
BATHING WELL AT RIM
WATER DEPTH TO OVERFLOW
FLOOR LOADING
41.7
(PROJECTED AREA)
68.5
PTS.
CUBE (FT 3 )
H70
SCALA CORNER™
254mm X 254mm
(10 X 10) DRAIN
OUTLET CUTOUT
406mm
(16)
1041mm
(41)
95mm
(3-3/4)
1-1/2" N.P.T.M. THREADS
60mm
(2-3/8)
1-1/2" O.D. TAILPIECE
4-7/8
(1524 x 1524 x 502mm)
42 x 28 In. (1067 x 711mm)
60 x 40 In. (1524 x 1016mm)
36 Lbs./Sq.Ft. (177 Kgs./Sq.m)
HIGH GLOSS
25mm (1)
INTEGRAL TILE
FLANGE (2) SIDES
464mm
18-1/4
502mm
ROUGH
(19-3/4)
FLOOR
INTEGRAL
FEET
SUPPORT
60 x 60 x 19-3/4 In.
94 Lbs. (42 Kg.)
761 Lbs. (342 Kg.)
80 Gal. (303 L)
14 In. (356mm)
41.7
68.5
Revised 2/08