American Standard 2476 Installatie-instructies Verzorging en onderhoud - Pagina 3
Blader online of download pdf Installatie-instructies Verzorging en onderhoud voor {categorie_naam} American Standard 2476. American Standard 2476 13 pagina's. Dual flush 2-piece toilet
Ook voor American Standard 2476: Installatie-instructies (4 pagina's)
Pagina afdrukken
10
ARM
TOP
NIPPLE
CRITICAL
LEVEL MARK
("C.L.") MUST
BE 1" ABOVE
OVERFLOW
PIPE
FLOAT
CUP
FILL
VALVE
VALVE
WATER LEVEL
BODY
ADJUSTMENT
ROD
ADJUSTABLE
HEIGHT
SHANK
WASHER
LOCK NUT
THREADED
SHANK
CONE WASHER
PARTS FOR WATER
CONNECTION
COUPLING NUT
(SEE STEP 9)
(HAND TIGHT ONLY)
12
FLUSH BUTTONS ON TANK
• Pressing both buttons at once will flush the half flush amount
.8 gal/flush or 3L/flush.
• The Partial Flush Button should line up over the blue actuator
on the flush tower in the tank.
• The Full Flush Button should line up over the white actuator
on the flush tower in the tank.
13
CARE AND CLEANING
When cleaning your toilet, wash it with mild, soapy water, rinse thoroughly with clear water and dry with a soft cloth. Avoid detergents,
disinfectants, or cleaning products in aerosol cans. NEVER use abrasive scouring powders or abrasive pads on your toilet seat. Some
bathroom chemicals and cosmetics may damage the seat's finish.
WARNING: Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This
!
damage can cause leakage and property damage.
American Standard shall not be responsible or liable for any tank fitting damage caused by the use of cleaners containing chlorine
(calcium hypochlorite).
Repair parts are determined by toilet tank number which can be found marked inside tank.
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
PART NO.
735130-400-XXX0A
738565-426.0070A
738565-427.0070A
7301143-0070A
7381002-400.0070A
7381002-401.0070A
7381003-XXX0A
034783-XXX0A
760127-XXX0A
760130-XXX0A
7381042-0070A
760134-0200A
PUSH
BUTTON
SET WATER
FLUSH
LEVEL HERE
VALVE
PARTIAL
FLUSH
ADJUSTMENT
FULL
FLUSH
ADJUSTMENT
BAYONET
RELEASE
SILICONE
SEAL
VALVE
SEAT
Diagram 1
REPAIR PARTS LIST
DESCRIPTION
TANK COVER WITH PUSH BUTTON
FLUIDMASTER 400A VALVE
FLUIDMASTER 400A VALVE
TANK COUPLING KIT #258
DUAL FLUSH VALVE
DUAL FLUSH VALVE
PUSH BUTTON ASSEMBLY - TOP MOUNT
BOLT CAP KIT
TOILET SEAT (ELONGATED RIM ONLY )
TOILET SEAT - SLOW CLOSE (ELONGATED RIM ONLY)
FLUSH VALVE SILICONE SEAL
HINGE KIT FOR SLOW CLOSE SEAT
ADJUSTMENTS
a.
Adjust water level. Water level should
be adjusted to level indicated on tank by
adjusting float cup.
See Step 11 for water level
adjustment method.
b.
Make sure Full Flush Adjustment is at
the bottom setting (0). A higher setting
will result in less water and is not
recommended.
c.
Make sure Partial Flush Adjustment is
at the bottom setting (0). A higher setting
will result in less water and is not
recommended.
NOTE: The Fill Valve does not have a refill
tube. The refill port on the Fluidmaster fill
valve is 100% blocked off. Please ensure that
the correct repair part is used as this fill valve
varies from the standard Fluidmaster 400A.
• To remove Flush Valve, apply slight downward pressure and twist it until the
flush valve disengages from the bayonet.
• To reinstall Flush Valve, reverse the above procedure making sure the blue
(Partial Flush Button) will line up with the Partial Flush Button on the Tank Lid.
Small button for
liquid waste.
.8 gal/flush
3L/flush
- 3 -
11
Turn on water supply.
Submerge the FLOAT CUP
under the water for 30
seconds. Adjust the water to
desired level by turning
WATER LEVEL ADJUSTMENT
ROD and moving FLOAT CUP
up or down.
Large button for
solid waste.
1.6 gal/flush
6L/flush
TANK NUMBER
4035.216
4035.516
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
7 3 01 1 4 4 - 1 0 0 R e v. G