Da-Lite Contour Electrol Instructieboek - Pagina 5

Blader online of download pdf Instructieboek voor {categorie_naam} Da-Lite Contour Electrol. Da-Lite Contour Electrol 9 pagina's. Installer friendly features
Ook voor Da-Lite Contour Electrol: Instructieboek (13 pagina's), Installateurshandleiding (2 pagina's), Instructieboek (4 pagina's), Instructieboek (8 pagina's), Instructieboek (8 pagina's)

Pagina afdrukken

SCREEN AdjUSTMENT FOR 120v SCREENS WITH A BUILT-IN LOW vOLTAGE CONTROL OR vPI

1. locate the wall switch and remove the cover plate from the 3-button wall switch and remove the switch from the

junction box.

2. locate the two tactile buttons on the back of the switch. They are square silver with black round buttons. See

figure 8 (VPI) or figure 10 (lVC) for diagram.

3. To adjust the down limit switch, press and hold the down tactile button until the lED on back of switch turns solid

red. This will put the motor in limit set mode. Turn the wall switch over and use the down button on front of

switch. Press and hold until the desired travel position is reached. If you travel to far down you can press the up to

move the screen upward. If you press and let go of either up or down button the motor will do a small jog in that

direction for finer adjustment of screen. once desired position is reached turn switch over press and hold down

tactile button until the lED on back of switch blinks red twice. The down limit is now set.

4. To adjust the up limit switch, press and hold the up tactile button until the lED on back of switch turns solid green.

This will put the motor in limit set mode. Turn the wall switch over and use the up button on front of switch. Press

and hold until the desired travel position is reached. If you travel to far up you can press the down to move the

screen downward. If you press and let go of either up or down button the motor will do a small jog in that direction

for finer adjustment of screen. once desired position is reached turn switch over press and hold up tactile button

until the lED on back of switch blinks green twice. The up limit is now set.

5. To test limit switch setting, press and release the up or down button on the wall switch to operate the screen.

6. Replace switch and cover plate on the wall.

IMPORTANT NOTE: The wall switch is REQuIRED to make any limit switch adjustments, EVEn if a third party control

system is used. Therefore, it is advised to wire the switch or provide a 3-conductor connection that is

accessible.

CAUTION: Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. This

screen comes standard with 0" or 2" black at the top. See the specification data sheet for details.

SCREEN AdjUSTMENT FOR 220v/240v SCREENS WITH A BUILT-IN LOW vOLTAGE CONTROL

1. Remove the cover plate from the 3-button wall switch and remove the switch from the junction box.

2. locate small 3-position switch on back of wall switch. (See figure 11)

CAUTION: Do not adjust for more drop than what was ordered. At least 1-1/2 wraps of fabric must remain on the roller. This

screen comes standard with 0" or 2" black at the top. See the specification data sheet for details.

3. To adjust the down limit switch, slide the 3-position switch to the down position. Press and hold the down button

to run the screen down to the desired stop position. Release the button to stop the screen. Do noT PuSH THE

SToP BuTTon.

4. When the screen is in the desired down position, slide the 3-position switch to the off (center) position. The down

limit switch is now set.

5. To adjust the up limit switch, slide the 3-position switch to the up position. Press and hold the up button to run the

screen up to the desired stop position. Release the button to stop the screen. Do noT PuSH THE SToP BuTTon.

6. When the screen is in the desired up position, slide the 3-position switch to the off (center) position. The up limit

switch is now set.

7 . To test limit switch setting, make sure the 3-position switch is in the off (center) position. Press and release the up

or down button on the wall switch to operate the screen.

8. Replace switch and cover plate on the wall.

NOTE: If stop button is pressed, the wall switch will reverse direction. To correct this, press the stop button again. This

will reset the switch. You will have to re-set both the up and the down settings.

IMPORTANT NOTE: The wall switch is REQuIRED to make any limit switch adjustments, EVEn if a third party control

system is used. Therefore, it is advised to wire the switch or provide a 4-conductor connection that is

accessible.