American Standard Town Square 2817 Installatie-instructies Verzorging en onderhoud - Pagina 2
Blader online of download pdf Installatie-instructies Verzorging en onderhoud voor {categorie_naam} American Standard Town Square 2817. American Standard Town Square 2817 4 pagina's.
Pagina afdrukken
6
INSTALL TOILET
a.
Position toilet squarely to wall and, with a rocking motion, press bowl
down fully on wax ring and flange.
Alternately tighten nuts until toilet is firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS OR
!
BASE MAY BE DAMAGED!
b.
Install bolt covers:
1.
Make sure that the bolt cover area on the toilet is clean and
dry (see figure). Use a dry piece of cloth or soap and water
if needed.
2.
Take plastic bolt cover and peel the brown protective film off
on both ends. The adhesive part is now visible and ready to
be placed on the toilet (see figure).
3.
Gently place the bolt cover on the toilet area (see picture) and if
everything is aligned, push bolt cover firmly so it remains in place.
4.
If not aligned, you can still take it off and put it back so it is aligned.
5.
Repeat Step 3 for second bolt cover which is to be placed on opposite side of the toilet.
6.
After 24 hours, the bolt cover adhesive has completely set off and if needed, you can remove/replace
as needed. The dual lock technology is now in place.
c.
Smooth off the bead of sealant around base. Remove excess sealant.
7
For Tanks/Bowls using Speed Connect System
(Tank mounting bolts pre-installed).
INSTALL TANK
a.
Install large rubber gasket over threaded outlet on bottom of tank and
lower tank onto bowl so that tapered end of gasket fits evenly into bowl
water inlet opening, and tank mounting bolts go through mounting
holes. Secure with metal washer/nut combo.
b.
With tank parallel to wall, alternately tighten nuts until tank is snugged
down evenly against bowl surface.
*
USE INCLUDED TOOL, NUT DRIVER, OR DEEP SOCKET RACHET.
!
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
8
INSTALL TOILET SEAT: Install toilet seat in accordance with manufacturer's directions.
9a
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL / COPPER
METAL FLANGED
FLARED TUBING
TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in water
leakage. Water supply tube or pipe
must extend at least 1/2" inside
threaded shank of valve (does not
apply to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
WARNING: Do not use plumber's putty, pipe dope, or any other sealant on the water supply connection to this tank. If the connection
!
leaks after hand tightening, replace the supply line. If the connection continues to leak with the new supply line, replace the fill valve.
Warranty is void if any type of sealant is used on the water supply connection.
CAUTION:
METAL SPIRAL
TUBING
LOCK NUT
LOCK NUT
EXISTING
EXISTING
WASHER
CONE
WASHER
EXISTING
COUPLING
COUPLING
NUT
NUT
WATER
WATER
SHUT-OFF
SHUT-OFF
Use existing
Use existing spiral
coupling nut
cone washer.
and washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
BOLTS
CLOSET FLANGE
9b
VINYL / BRAIDED
CONNECTOR
LOCK NUT
COUPLING
NUT
WATER
SHUT-OFF
Captive cone
washers already
included. No
additional washers
needed.
- 2 -
BOLT COVER
Back Side
Peel both protective films off
and stick bolt cover to toilet.
Front Side
BOLT COVER
CLOSET BOLT
TANK MTG.
RUBBER
BOLTS PRE-
GASKET
INSTALLED
WASHER/
NUT
COMBO
With correct washers in
place (see Step 9a),
tighten COUPLING NUT
1/4 turn beyond hand tight.
DO NOT OVERTIGHTEN.
73 0 1 4 5 6 - 1 0 0 R e v. A
NUT