Ekinex EK-ET2-TP-R Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Ekinex EK-ET2-TP-R. Ekinex EK-ET2-TP-R 8 pagina's. Room temperature controller with humidity and co2 equivalent regulator

Pagina afdrukken

Plate

Type

Appearance

code *

EK-PQS-...

1-fold **

EK-PRS-...

1-fold **

EK-P2G-...

2-fold ***

EK-P2S-...

2-fold ***

(*) To be completed with the extension for colour, material and finishing

(**) For mounting without frame ('NF) it requires the EK-TAQ adapter

(***) For mounting without frame ('NF) it requires the EK-A71-... adapter

Frame

The room temperature controller can be completed by a

square 1-fold frame or by a rectangular 2-fold frame of the

flank or form series. The 'NF (No Frame) versions of the

pushbutton do not require any frame.

Mounting

The device has degree of protection IP20, and is therefo-

re suitable for use in dry interior rooms. The installation of

the device requires the following steps:

Mounting with frame, round flush-mounting box

Carry out the following steps:

• fix the metallic support (h) with the screws (g) on a

flush-mounting box (i) provided with suitable fixing ho-

les;

• snap a square frame (f) of the form or flank series, in-

serting it from the rear of the preassembled thermostat-

adapter (d+e);

• insert the bus terminal, previously connected to the bus

cable, in its slot on the rear side (see also: "Connection

of the KNX bus line"). At this point it is recommended

to carry out the commissioning of the pushbutton (see

also "Configuration and commissioning") or at least the

download of the physical address;

Mounting with frame

a) 1-fold plate (square, with 60 x 60 mm window)

b) Rocker

c) Screws (for device)

d) Device

e) Adapter (delivered preassembled on the device)

f) Frame (square, form or flank series)

g) Screws (for metallic support)

h) Metallic support

i) Flush-mounting box (not delivered by ekinex

Window

modularity [mm]

60 x 60

55 x 55 (1)

60 x 60 (1)

60 x 60 (2)

)

• insert thermostat and adapter (d+e), completed with

the frame (f), in the metallic support (h). Mounting the

pushbutton follow the indication TOP (arrow tip pointing

up) on the rear side of the device;

• tighten thermostat, adapter and frame (d+e+f) on the

metallic support (h) with the two screws (c);

• snap the plate (a);

• snap the rocker (b) to complete the installation.

Mounting with no frame, round flush-mounting box

Carry out the following steps:

• insert the metallic support (f) on the adapter (g);

• fix adapter and metallic support (f+g) with the screws

(e) on a flush-mounting box (h) provided with suitable

fixing holes;

• insert the bus terminal, previously connected to the bus

cable, in its slot on the rear side (see also: "Connection

of the KNX bus line"). At this point it is recommended

to carry out the commissioning of the pushbutton (see

also "Configuration and commissioning") or at least the

download of the physical address;

• insert the thermostat (d) in the support-adapter (f+g).

Mounting the device follow the indication TOP (arrow

tip pointing up) on the rear side of the device;

• tighten the device on the support-adapter (f+g) with the

two screws (c);

• snap the plate (a);

• snap the rocker (b) to complete the installation.

Mounting with no frame

a) 1-fold plate (square, with 60 x 60 mm window)

b) Rocker

c) Screws (for device)

d) Device

e) Screws (for metallic support)

f) Metallic support

g) Adapter for 'NF series (delivered with the device)

h) Flush-mounting box (not delivered by ekinex

Mounting with rectangular flush-mounting box

Carry out the following steps:

• insert the metallic support (f) on the adapter (g);

• for versions provided with frame only: snap a rectangu-

lare frame (f) of either form or flank series, starting from

the back side of the support-adapter group (f+g) ;

• fix adapter and metallic support (f+g) (and eventually

the frame, h) with the screws (e) on a flush-mounting

box (i) provided with suitable fixing holes;

• insert the bus terminal, previously connected to the bus

cable, in its slot on the rear side (see also: "Connection

of the KNX bus line"). At this point it is recommended

to carry out the commissioning of the pushbutton (see

also "Configuration and commissioning") or at least the

download of the physical address;

• insert the thermostat (d) in the support-adapter (f+g).

Mounting the device follow the indication TOP (arrow

tip pointing up) on the rear side of the device;

• tighten the device on the support-adapter (f+g) with the

min 0,3 m

)