Ekinex KNX EK-E32-TP-NFW Snelstarthandleiding - Pagina 2

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Ekinex KNX EK-E32-TP-NFW. Ekinex KNX EK-E32-TP-NFW 5 pagina's. Pushbutton

Pagina afdrukken

Delivery

The delivery of the pushbutton includes a metallic support

for round flush-mounting box, the fixing screws (2 pairs)

and the KNX terminal block for connection of the bus line.

Accessories for the pushbutton

The pushbutton is completed through a separate order of:

• a set of rockers that allows the use it as 2-fold or

4-fold pushbutton;

• a square frame of the ekinex

for the 'NF - No Frame versions).

Rockers

Three-positions rockers with central neutral position have

to be mounted on the pushbutton. Pushing one side of

a rocker (for example the upper one), the pushbutton

sends on the bus a telegram for switching on, increasing

the brightness of luminaires or raising the blinds, while

pushing the other side (for example the lower one), it sen-

ds a telegram for switching off, reducing the brightness of

luminaires or lowering the blinds. Each channel is equip-

ped with LEDs which can be freely programmed as status

feedbacks of the loads and as orientation nightlight (EK-

ED2-TP versions only.

Code set of

Appea-

Nr. and type of

rockers *

rance

EK-TRV-xxx

EK-TQQ-xxx

EK-TRO-xxx

(*) To be completed with the extension for colour and material

Note on installation of rockers

To assemble the rockers on their seats, the fixing teeth

must be aligned vertically.

Frame

The pushbutton can be completed by a square 1-fold fra-

me of the flank or form series. Using the templates EK-

DFO and EK-DFL it is also possible mounting side by side

two devices of FF series both completed by square fra-

mes respectively of form or flank series.

Note. The set of rockers and the optional frame for

completing the device have to be ordered separa-

tely. For more information, see also the ekinex

duct catalog or browse www.ekinex.com

form or flank series (not

Rockers modu-

rockers

larity [mm]

2 rectangular

40 x 80

4 square

40 x 40

4 rectangular

80 x 20

correct

mounting

not possible

(fixing teeth

in horizontal)

Code *

EK-FOQ-GAx

EK-FOQ-GBx

EK-FLQ-GAx

EK-FLQ-GBx

(*) To be completed with the extension for colour and material

Mounting

The device has degree of protection IP20, and is there-

fore suitable for use in dry interior rooms. Mounting the

device carry out the following steps:

• fix the metallic support (5) with the pair of screws (6) on

the flush-mounting box (7) equipped with fixing holes at

60 mm distance;

• insert pushbutton (3) in the metallic support (5).

Mounting the device follow also the indication TOP (ar-

row tip pointing up) on the front side of the device;

• snap a square frame (4) of the form or flank series, in-

serting it from the rear of the pushbutton (3);

• enter the bus terminal block, previously connected to

the bus cable in its slot on the rear side (see also: "Con-

nection of the KNX bus line"). At this point it is recom-

mended to carry out the commissioning of the device

(see also "Configuration and commissioning") or at le-

ast the download of the physical address;

• fasten the device on the metallic support supplied with

the pair of screws (2);

• snap the rockers (1) for the operation of the device.

Note. The supplied plastic screws (# 2) must be

used exclusively to fix the push-button panel in

position, therefore they must not be tightened with

excessive force (max. torque 0.4 Nm).

1) Rockers (to be ordered separately)

2) Fixing screws (for device)

3) Device

4) Frame of form or flank series (to be ordered separately)

5) Metallic mounting support

6) Fixing screws (for metallic support)

7) Flush-mounting box (not delivered by ekinex)

Note. The screws supplied in the package are su-

pro-

itable for standard installations. For more specific

applications, where the screws have to be replaced,

only flat-head screws must be used. The screws for

the metal support must be tightened with a max. tor-

que of 1.0 Nm.

Material

Package

plastic

1 pcs.

metal

plastic

1 pcs.

metal

Dimens.

[mm]

86 x 86

94 x 80