Ekinex EK-BO1-TP-RMA Snelstarthandleiding - Pagina 3

Blader online of download pdf Snelstarthandleiding voor {categorie_naam} Ekinex EK-BO1-TP-RMA. Ekinex EK-BO1-TP-RMA 3 pagina's. Modbus / knx interface for rdz air handling units

Pagina afdrukken

Ekinex EK-BO1-TP-RMA Snelstarthandleiding

Connection of the KNX bus line

The connection of the KNX bus line is made with the ter-

minal block (red / black) included in delivery and inserted

into the slot at the bottom of the housing.

Characteristics of the KNX terminal block

• spring clamping of conductors

• 4 seats for conductors for each polarity

• terminal suitable for KNX bus cable with single-wire

conductors and diameter between 0.6 and 0.8 mm

• recommended wire stripping approx. 5 mm

• color codification: red = + (positive) bus conductor,

black = - (negative) bus conductor

Warning! The electrical connection of the device can

be carried out only by qualified personnel. The incor-

rect installation may result in electric shock or fire.

Before making the electrical connections, make sure

the power supply has been turned off.

Configuration and commissioning

Configuration and commissioning of the device require

the use of the ETS® (Engineering Tool Software) program

V4 or later releases. These activities must be carried out

according to the design of the building automation system

done by a qualified planner.

Note. The configuration and commissioning of KNX

devices require specialized skills.To acquire these

skills, you should attend the workshops at KNX certi-

fied training centers.

Configuration

For the configuration of the device parameters the corre-

sponding application program or the whole ekinex® pro-

duct database must be loaded in the ETS program. For

detailed information on configuration options, refer to the

application manual of the device available on the website

www.ekinex.com.

Code

EK-BO1-TP-RMA

Commissioning

For commissioning the device the following activities are

required:

• make the electrical connections as described above;

• turn on the bus power supply;

• switch the device operation to the programming mode

• by pressing the programming pushbutton located on

the front side of the housing. In this mode of operation,

the programming LED is turned on;

• download into the device the physical address and the

configuration with the ETS® program.

At the end of the download the operation of the device

automatically returns to normal mode; in this mode the

programming LED is turned off. Now the bus device is

programmed and ready for use.

Reset of the device

To reset the device remove the bus connection by ex-

tracting the bus terminal from its seat. Keeping pressed

the programming pushbutton, reinsert the bus terminal in

his seat; the programming LED blinks fast. Release the

programming button and remove the bus terminal again;

the reset was carried out. Now you need to address and

configure again the device via ETS.

Application program

(## = version)

APEKBO1RMATP##.knxprod

Warning! The reset restores the device back to the

state of delivery from the factory. The address and

the value of the parameters set during confi guration

will be lost.

Marks

• KNX

• CE: the device complies with the Low Voltage Directi-

ve (2014/35/UE) and the Electromagnetic Compatibility

Directive (2014/30/UE)

Maintenance

The device is maintenance-free. To clean use a dry cloth.

It must be avoided the use of solvents or other aggressive

substances.

Disposal

At the end of its useful life the product described in this da-

tasheet is classified as waste from electronic equipment

in accordance with the European Directive 2012/19/UE

(WEEE), and cannot be disposed together with the muni-

cipal undifferentiated solid waste.

Warning! Incorrect disposal of this product may cau-

se serious damage to the environment and human

health. Please be informed about the correct disposal

procedures for waste collecting and processing provi-

ded by local authorities.

Warnings

• Installation, electrical connection, configuration and

commissioning of the device can only be carried out

by qualified personnel in compliance with the appli-

cable technical standards and laws of the respective

countries

• Opening the housing of the device causes the imme-

diate end of the warranty period

• In case of tampering, the compliance with the essen-

tial requirements of the applicable directives, for which

the device has been certified, is no longer guaranteed

• ekinex

KNX defective devices must be returned to the

manufacturer at the following address: Ekinex S.p.A.

Via Novara 37, I-28010 Vaprio d'Agogna (NO)

Other information

• The instruction sheet must be delivered to the end

customer with the project documentation

• For further information on the product, please contact

the ekinex

technical support at the e-mail address:

[email protected] or visit the website www.ekinex.

com

• KNX

and ETS

are registered trademarks of KNX

Association cvba, Brussels

ges to this documentation without notice.