Canon PIXMA MP610 Series Servicehandleiding - Pagina 7

Blader online of download pdf Servicehandleiding voor {categorie_naam} Canon PIXMA MP610 Series. Canon PIXMA MP610 Series 45 pagina's. All-in-one photo inkjet printer
Ook voor Canon PIXMA MP610 Series: Start Here (2 pagina's), Aanvullende handleiding (6 pagina's), Brochure & specificaties (2 pagina's), Snelstarthandleiding (40 pagina's), Snelstarthandleiding (2 pagina's)

Pagina afdrukken
Canon PIXMA MP610 Series Servicehandleiding
Multiple ink tanks of
the same color installed.
Ink tank in a wrong
position.
Warning: The ink
absorber becomes
almost full.
The connected digital
camera or digital video
camera does not support
Camera Direct Printing.
Automatic duplex
printing cannot be
performed.
Failed in automatic
print head alignment.
The remaining ink
amount unknown.
Ink tank not recognized. [1684] U140 The following ink tank cannot be
Ink tank not recognized. [1410 to
No ink (no raw ink).
Non-supported hub
*1: Only for models supporting CD / DVD printing
*2: Only for models not supporting CD / DVD printing
[1681] U071 More than one ink tank of the
following color is installed.
[1680] U072 Some ink tanks are not installed in
place.
[1700,
---
Contact the support center or
1701]
service center for ink absorber
replacement. Press [OK] to
continue printing.
[2001]
---
The device may be incompatible.
Remove the device and check the
manual supplied with the connected
device.
[1310]
---
This paper is not compatible with
duplex printing. Remove the paper
and press [OK].
[2500]
---
Auto head align has failed. Press
[OK] and repeat
operation. <See manual>
[1683] U130 (Applicable ink tank icon)
The remaining level of the
following ink cannot be correctly
detected. Replace the ink tank.
recognized.
(Applicable ink tank icon)
U150 The following ink tank cannot be
1419]
recognized.
(Applicable ink tank icon)
[1688] U163 The following ink has run out.
Replace the ink tank.
(Applicable ink tank icon)
[2002]
---
An unsupported USB hub is
connected. Remove the hub.
feeder, and press the OK button.
Replace the wrong ink tank(s) with the correct one
(s).
Install the ink tank(s) in the correct position.
Replace the ink absorber, and reset its counter.
[See
3-3. Adjustment / Settings, (6) Service
mode.]
Pressing the OK button will exit the error, and
enable printing without replacing the ink absorber.
However, when the ink absorber becomes full, no
further printing can be performed unless the
applicable ink absorber is replaced.
Remove the cable between the camera and the
machine.
The paper length is not supported for duplex
printing.
Press the OK button to eject the paper being used
at error occurrence.
Data which was to be printed on the back side of
paper at error occurrence is skipped (not printed).
Press the OK button to clear the error, then
perform the automatic print head again.
(In the MP610, use Matte Photo Paper MP-101.)
An ink tank which has once been empty is
installed. Replace the applicable ink tank with a
new one. Printing with a once-empty ink tank can
damage the machine.
To continue printing without replacing the ink
tank(s), press the Stop/Reset button for 5 sec. or
longer to disable the function to detect the
remaining ink amount. After the operation, it is
recorded in the machine EEPROM that the
function to detect the remaining ink amount was
disabled.
A non-supported ink tank is installed (the ink tank
LED is turned off). Install the supported ink tanks.
A hardware error occurred in an ink tank (the ink
tank LED is turned off). Replace the ink tank(s).
Replace the empty ink tank(s), and close the
scanning unit (printer cover).
Printing with an empty ink tank can damage the
machine.
To continue printing without replacing the ink
tank(s), press the Stop/Reset button for 5 sec. or
longer to disable the function to detect the
remaining ink amount. After the operation, it is
recorded in the machine that the function to detect
the remaining ink amount was disabled.
Remove the applicable USB hub from the
PictBridge (USB) connector.
5 / 43