Canon PIXMA MP810 Servicehandleiding - Pagina 10
Blader online of download pdf Servicehandleiding voor {categorie_naam} Canon PIXMA MP810. Canon PIXMA MP810 20 pagina's. Personal printing guide
Ook voor Canon PIXMA MP810: Gebruikershandleiding (2 pagina's), Snel aan de slag (1 pagina's), Aanvullende handleiding (6 pagina's), Snelstarthandleiding (38 pagina's)
Pagina afdrukken
becomes almost full.
The connected digital
camera or digital video
camera does not support
Camera Direct Printing.
Automatic duplex printing
cannot be performed.
Failed in automatic print
head alignment.
The remaining ink amount
unknown.
Ink tank not recognized.
Ink tank not recognized.
No ink (no raw ink).
Scanning unit (printer cover)
open.
Scanner lock switch locked.
2-2. Service Call Errors (by Cyclic Blinking of Alarm and Power LEDs)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink, and the corresponding error code is displayed on the LCD.
Cycles of blinking
of Alarm and
Power LEDs
2 times
Carriage error
3 times
Line feed error
4 times
Purge cam sensor error
5 times
ASF (cam) sensor error
1701]
for ink absorber replacement. Press [OK]
to continue printing.
[2001]
---
The device may be incompatible. Remove
the device and check the manual supplied
with the connected device.
[1310]
---
This paper is not compatible with duplex
printing. Remove the paper and press
[OK].
[2500]
---
Auto head align has failed. Press [OK] and
repeat
operation. <See manual>
[1683]
U130
(Applicable ink tank icon)
The remaining level of the following ink
cannot be correctly detected. Replace the
ink tank.
[1684]
U140
The following ink tank cannot be
recognized.
(Applicable ink tank icon)
[1410 to
U150
The following ink tank cannot be
1419]
recognized.
(Applicable ink tank icon)
[1688]
U163
The following ink has run out. Replace the
ink tank.
(Applicable ink tank icon)
[1200]
---
Cover is open. Close cover.
[5020]
---
Release the scanner lock switch and turn
the power off and back on.
Error
Error
code
[5100]
[6000]
[5C00]
[5700]
Adjustment / Settings, (6) Service
Pressing the OK button will exit the error, and enable
printing without replacing the ink absorber. However, when
the ink absorber becomes full, no further printing can be
performed unless the applicable ink absorber is replaced.
Remove the cable between the camera and the machine.
The paper length is not supported for duplex printing.
Press the OK button to eject the paper being used at error
occurrence.
Data which was to be printed on the back side of paper at
error occurrence is skipped (not printed).
Press the OK button to clear the error, then perform the
automatic print head again.
(In the MP810, use Matte Photo Paper MP-101.)
An ink tank which has once been empty is installed. Replace
the applicable ink tank with a new one.Printing with a once-
empty ink tank can damage the machine.
To continue printing without replacing the ink tank(s), press
the Stop/Reset button for 5 sec. or longer to disable the
function to detect the remaining ink amount. After the
operation, it is recorded in the machine EEPROM that the
function to detect the remaining ink amount was disabled.
A non-supported ink tank is installed (the ink tank LED is
turned off). Install the supported ink tanks.
A hardware error occurred in an ink tank (the ink tank LED is
turned off). Replace the ink tank(s).
Replace the empty ink tank(s), and close the scanning unit
(printer cover).
Printing with an empty ink tank can damage the machine.
To continue printing without replacing the ink tank(s), press
the Stop/Reset button for 5 sec. or longer to disable the
function to detect the remaining ink amount. After the
operation, it is recorded in the machine that the function to
detect the remaining ink amount was disabled.
Close the scanning unit (printer cover).
Unlock the scanner lock switch, turn the machine off, then
turn the machine on again.
Conditions
An error occurred in the carriage encoder signal.
An error occurred in the LF encoder signal.
An error occurred in the purge unit.
This error takes place when feeding paper from the - Sheet feed unit
1-5
mode.]
Solution
(Replacement of listed parts, which
are likely to be faulty)
- Carriage unit
- Timing slit film
*
- Logic board
- Carriage motor
- Timing sensor unit
- Timing slit disk film
- Feed roller
*
- Logic board
- Paper feed motor
- Purge unit
*
- Logic board