AmerTac Zenith Qi Gebruikershandleiding

Blader online of download pdf Gebruikershandleiding voor {categorie_naam} AmerTac Zenith Qi. AmerTac Zenith Qi 2 pagina's. Wireless charger

Pagina afdrukken

Qi Wireless Charger Owners Manual

PM1001QIPCB

What's Included

1. Power Supply Cable

2. Charging area

3. Light indicator Area

4. Owner's Manual

QI™ COMPATIBILITY

This product complies with the Qi wireless charging standard

set by the WPC. It can charge any device marked with the

Qi logo,

NOTE: The Qi symbol is a trademark of the Wireless Power Consortium

IMPORTANT SAFETY INFORMATION:

IMPORTANT SAFETY INSTRUCTIONS

For use with 120V, 60Hz electrical power supply only. Not to be

used with travel converters.

SAVE THESE INSTRUCTIONS

Read and understand all of these instructions before using this

product. Read all instructions and warnings prior to using this

product. Improper use of this product may result in product

damage, excess heat, toxic fumes, fire or explosion, for

which damages you ("Purchaser"), and not AmerTac

("Manufacturer") are responsible.

Keep these instructions in a safe place for future reference.

SPECIFICATIONS

Model: PM1001QIPCB

Product Standard: Qi

TX Input: DC5V/1.5A

RX Output: DC5V/1000mA Max

Working Frequency: 110-205KHz

Size: 6.2" (158mm) L x 3.3" (85mm) W x 0.4" (9mm) D

Compatibility: Qi-enabled devices, iPhone 8, iPhone 8 Plus, iPhone X or later,

Samsung Galaxy S8, S8 Plus/S8+, S7, S7 Edge, Note 5 & S6 Edge Plus, Samsung

Galaxy S6, S6 Edge Nexus 5, etc., Nokia Lumia 920, LG Nexus 5/4/7, Samsung

Galaxy S3/S4/S5, Note 3/Note2 with receiver card or receiver case, ect.

CHARGING YOUR WIRELESS DEVICE

•

Connect the Power Supply Cable to Qi Charging Pad and to

any 5V USB power supply (not included). Be sure connections

are secure.

•

You will see a blue LED light for about 3 seconds then a green

light will show through charging pad at the Light Indicator Area

noted in the "What's Included" section of this manual. You may

also hear a tone from your device indicating it is connected and

charging properly.

•

Place your Qi compatible wireless device on charging pad.

When the device is charging, the LED light color will change from

green to blue. When the device is removed from the charging

pad the LED will turn back to green. Your device may feel warm

to the touch as it is charging or if it remains on the charger when

fully charged. This is normal. The device should be removed

when fully charged as indicated on your device.

•

Remove device when fully charged. Your device may feel warm

to the touch as it is charging. This is normal.

Limited Warranty

Under normal use and conditions, AmerTac provides to the original

purchaser of this product a one year limited express warranty that is set

forth in the Limited Warranty stated in full at www.amertac.com/warranties.

The Limited Warranty is in lieu of all other express or implied warranties or

250 Boulder Dr.

liabilities subject to the exceptions explained fully in the Limited Warranty

Breinigsville, PA 18031

610-336-1330

on the website.

www.amertac.com

Made in China /

Fabriqué en Chine /

Fabricado en China

Zenith is a registered trademark and used under license to AmerTac

Zenith est une marque de commerce déposée et utilisée sous licence par AmerTac.

I18-0025-A

Zenith es una marca registrada y se utiliza bajo licencia por AmerTac

FCC Statement

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the following measures:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any interference received, including interference that may cause

undesired operation.

Note: Modifications to this product will void the user's authority to operate this equipment.

WARNING

•

This product may represent a possible shock or fire hazard if

improperly installed or attached in any way. To prevent

overheating and electrical shock do not operate in small

enclosed spaces.

•

For questions or instructions for the various ways to charge using

this device refer to the "Charging Your Wireless Device" section

of this manual.

•

Do not store device in high-temperature environment, including

heat caused by intense sunlight or other forms of heat. Do not

place device in fire or other excessively hot environments.

•

Do not operate in wet locations or immerse in water.

•

Do not disassemble this device or attempt to re-purpose or

modify it in any manner.

•

Do not attempt to replace any part of this device.

•

Keep away from devices with magnetic stripe or chip (ID cards,

bank cards, etc.).

•

Keep at least 22 cm / 9 in away from medical implants to avoid

interference.

•

Remove charger from power when not in use.

•

Do not charge with any material or object between charger

and device.

•

Do not place any metallic or aluminum material on charging

pad.

•

Do not use broken adaptors, or cables.

•

Do not squeeze, bend or scratch the inductive charger.

•

If this device is accessible to or may be used by a minor,

purchasing adult agrees to be solely responsible for providing

supervision, instruction, and warnings. Purchaser agrees to

defend, indemnify, and hold Manufacturer harmless for any

claims or damages arising from unintended use or misuse by a

minor.

•

All products have gone through a thorough quality assurance

inspection. If you find that your device is excessively hot, is

emitting odor, is deformed, abraded, cut or is experiencing or

demonstrating an abnormal phenomenon, immediately stop all

product use and contact Manufacturer.

•

To comply with FCC RF exposure compliance requirements, the

wireless charging base must be used with a separation distance

of at least 10cm/ 4 in from all persons.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.