Astro Pneumatic 1442 Handmatig
Blader online of download pdf Handmatig voor {categorie_naam} Astro Pneumatic 1442. Astro Pneumatic 1442 4 pagina's. 13 inch nut/thread setting hand riveter kit with 3pc metric and 3pc sae mandrel/nosepiece sets and rivet nut assortment
Pagina afdrukken
MODEL:
WARNING
Study, understand and follow all instructions provided with this
product. Read these instructions carefully before installing,
operating, servicing or repairing this tool. Keep these instructions
in a safe accessible place.
INTENDED USE OF THE TOOL
This tool is intended to be used to install metric M5, M6, M8
and SAE 10-24, 1/4-20, 5/16-18 rivet nuts. Do not use this tool
outside of the designed intent. Never modify the tool for any
other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear appropriate
safety equipment and clothing when using this product.
Study, understand and follow all instructions provided with
this product. Failure to read and follow all warnings and
operating instructions may result in damages and serious
injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and By standers).
• Never use this tool for any application other than for which
it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
DRILL SIZE GUIDE
Metric
Nut Size
Drill Size
M4
6mm (7/32")
M5
7mm (9/32")
M6
9mm (3/8")
M8
11mm (7/16")
13" NUT/THREAD SETTING HAND RIVETER KIT
WITH 3PC METRIC AND 3PC SAE MANDREL/NOSEPIECE SETS
AND RIVET NUT ASSORTMENT
1442
SAE
Nut Size
Drill Size
10-24
7mm (9/32")
1/4-20
10mm (13/32")
5/16-18
11mm (7/16")
MADE IN CHINA
PRODUCT TYPE:
13" NUT/THREAD SETTING HAND RIVETER KIT
WITH 3PC METRIC AND 3PC SAE MANDREL/NOSEPIECE SETS
AND RIVET NUT ASSORTMENT
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original user against defective
material or workmanship for a period of 1 year (except where noted on our price
schedule) from the date of 1st use. Astro reserves the right to determine whether the
product failed because of defective material, workmanship or other causes and to charge
back for missing parts. Astro Pneumatic Tool Co., at its discretion, will repair products
covered under this warranty free of charge. The distributor should direct the original user
to return the product (with the exceptions listed below) with the distributor's name,
address, adequate proof of date of purchase or a copy of warranty card, and a short note
explaining the problem. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
• If one part of this product fails, please do not return the entire product. Astro will
replace free of charge component parts of this product that fail within 1 year of first
use by the original user. Items included in this category include but are not limited
to kits, hand tool kits and any other product where there are multiple items or
components that make up the unit. Please contact the phone number below in
order to obtain the replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives must perform all
warranty repairs. Any repair to the product by unauthorized service representatives
voids this warranty. The rights under this warranty are limited to the original user and may
not be transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or implied, including warranties
of merchantability and fitness for a particular purpose. Some states do not allow the
exclusion of limitations of incidental or consequential damages so the
above limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
When unpacking, check the parts diagram and part number
listing on page 4 to make sure all parts are included. If any
parts are missing or damaged, please call your distributor.
PRODUCT INFORMATION:
• New "Toolless Quick-Change Head" design allows for easy
changing of mandrels and nose pieces by hand
• Disassembly of tool never required, unique spring loaded inner hex
sleeve automatically locks the rotation of hand installed mandrels
• Patented structure increases power and reduces shock
• Shorter handle with double compound hinges
that maximize leverage
• 6 interchangeable mandrel/nosepiece sets in Metric
M5, M6, & M8 and in SAE 10-24, 1/4-20, & 5/16-18
• Includes 10 pieces of each of the following rivet nuts:
M5, M6, M8, 10-24, 1/4-20 and 5/16-18
• Ideal for working in hard-to-reach areas
• Ergonomic grip for easy operation
SPECIFICATIONS:
Weight: 2.43 lbs. (1100g)
Length: 13" (330mm)
Max. Working Stroke: 9mm
Max. Effective Working Stroke: 7mm
Arm Force Multiplier: 30
DO NOT DISCARD – GIVE TO USER
Page 1