Flying Industry Development S1UD-DC24 Beknopte handleiding - Pagina 2

Blader online of download pdf Beknopte handleiding voor {categorie_naam} Flying Industry Development S1UD-DC24. Flying Industry Development S1UD-DC24 3 pagina's. Rf wireless remote control radio controller with delay time function / transmitter & receiver
Ook voor Flying Industry Development S1UD-DC24: Beknopte handleiding (2 pagina's)

Pagina afdrukken
Control mode Momentary: Press and hold -> On; Release -> Off.
Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)
Release button 1: Turn off Receiver 1 (disconnect B and C, connect A and B)
If you set delay time, such as 20 seconds:
Press and hold button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)
After 20 seconds, Turn off Receiver 1 automatically (disconnect B and C, connect A and B). And the relay couldn't be turned off by pressing any
button within 20 seconds.
...
Press and hold button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)
Release button 12: Turn off Receiver 12 (disconnect B and C, connect A and B)
If you set delay time, such as 20 seconds:
Press and hold button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)
After 20 seconds, Turn off Receiver 12 automatically (disconnect B and C, connect A and B). And the relay couldn't be turned off by pressing any
button within 20 seconds.
Setting control mode Latched: Connect Jumper-1 and Jumper-2.
Control mode Latched: Press -> On, other relays Off; Press another button -> Off.
Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)
Press other button: Turn off Receiver 1 (disconnect B and C, connect A and B)
If you set delay time, such as 10 seconds:
Press button 1: Turn on Receiver 1 (connect B and C, disconnect A and B)
After 10 seconds, Turn off Receiver 1 automatically (disconnect B and C, connect A and B). Or press other button within 10 seconds: Turn off
Receiver 1 immediately.
...
Press button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)
Press other button: Turn off Receiver 12 (disconnect B and C, connect A and B)
If you set delay time, such as 10 seconds:
Press button 12: Turn on Receiver 12 (connect B and C, disconnect A and B)
After 10 seconds, Turn off Receiver 12 automatically (disconnect B and C, connect A and B). Or press other button within 10 seconds: Turn off
Receiver 12 immediately.
Delay time setting function:
Press the setting button, the LED off, that means enter into the delay time setting mode.
Then you can set delay time through pressing the learn button. Press the learn button, LED will flash once, that means the delay time increase 1
seconds, if you want to delay 30 seconds, you need to press the learn button with 30 times.
You can set longest delay time to 99 seconds.
Press the setting button again, the delay time what you have set will be preserved forever even if you turn off power. After the delay time is
preserved by the system, LED will flash 3 times, the system will quit the delay time setting mode.
For example, when you use this receiver to control one lamp, and you already set 30 seconds delay time, you can press button 1 to turn on the
lamp, and the lamp will turn off automatically after 30 seconds. If you don't need the delay function, you should clear the delay time.
Clear delay time:
If you don't want to set the delay time, you can operate as following:
Press the setting button and enter into the delay time setting mode, the delay time what you have set will be cleared automatically.
Press the setting button again, LED will flash 3 times, the system will quit the delay time setting mode.
Note:
We have learned remote control to the receiver. If you don't want the receiver to work with the remote control, you can delete all codes of remote
controls, which are stored in the receiver.
Operation: Press and hold the learn button of receiver until LED begin flashes slowly; release the button, LED keeps slow flash. That means all
stored codes have been deleted successfully.
Learning the button of remote control:
1) Press the learn button of receiver, LED off. The receiver enters into status of LEARNING.
2) Press any one button on remote control. If LED flashes 3 times and turns off, it means learning is successful.
3) When receiver is in the status of LEARNING, you should learn the remote control within 10 seconds, or the receiver will quit the status of
LEARNING after 10 seconds.
4) The receiver can learn 16 remote controls with different codes.
SHENZHEN GUIYUAN INDUSTRY DEVELOPMENT CO.,LTD
Http://www.carymart.com