Canor AI 1.20 Gebruikershandleiding - Pagina 5
Blader online of download pdf Gebruikershandleiding voor {categorie_naam} Canor AI 1.20. Canor AI 1.20 6 pagina's.
Pagina afdrukken
Basic functions of reproduction
Plug the power cord in AI 1.20. Turn on the AI 1.20 with the Power Main switch, which is located on the back
panel. When you turn on the main switch, the AI 1.20 will set into stand-by mode - the red LED diode on the
front panel lights up. After pressing the Power button (on the front panel or on the remote control) controlled
turning-on sequence gets initiated, the CANOR logo lights up and then the slow start-up of voltage begins.
Output relay connects the signal to the last selected input if the main power supply does not get diconnected.
During the first turning on or disconnecting the main power supply IN1 input gets preselected and the volume
level is set to -44dB. Volume is being set in 63 steps by 1dB. The highest volume is 0dB, the lowest being -
63dB. Another step is MUTE. You can control the volume with a big control knob on the front panel. The
volume is being controlled by a relay attenuator with an accuracy of concurrence better than 0.05dB.
You can connect both 4 and 8 Ohm loudspeakers to speaker terminal pairs on the back of AI 1.20.
MONOBLOCK mode:
As the amplifier has all its basic functions controlled electronically, we have capitalized on this advantage and
adjusted amplifier control the way in order to be able to use a stereo amplifier as a monoblock. We therefore had
developer a special protocol and a C-link communication interface.
This solution benefits from a great advantage, hence the monoblocks do not need a control preamplifier and
AI 1.20 can thus be used as an integrated stereo amplifier and as a monoblock. Attenuators ensure absolute
channels concurrence. Two AI 1.20 get connected by a data cable via C-link bus and at this moment one
ampplifier becomes a MASTER and the other one a SLAVE. MASTER amplifier then takes over the entire
control of both amplifiers synchronous-wise. SLAVE amplifier has all the control elements turned off.
Important:
-
XLR inputs are dedicated to use only in monoblock mode.
-
Dedicated set of speaker terminals on back panel for use in monoblock mode.
Interconnecting two AI1.20 amplifiers by a data cable must be carried out when both amplifiers are
turned off!! Caution! Make all connections only if the device is disconnected from the mains!
Specificatons :
Stereo output power:
Monoblock output power :
Input sensitivity:
Frequency range:
Input impedance:
Stereo Inputs:
Monoblock Inputs:
Total Harmonic Distortion:
Signal-to-noise ratio:
Signal-to-noise ration monoblock:
Power:
Dimensions (WxHxD):
Weight:
Guarantee conditions:
Your CANOR AI 1.20 integrated class-A amplifier is guaranteed against any defect in materials and
workmanship for a period of 24 months.
The warranty only applies if an original proof of purchase and acknowledged certificate of warranty can be
furnished. The warranty covers defects in materials and labor, but does not cover misuse, unauthorized
modifications, and external causes such as acts of nature.
2 x 50W / 4 Ohm
2 x 30W / 8 Ohm
1 x 130W / 4 Ohm
1 x 100W / 8 Ohm
500mV
20 - 25 000Hz -0,5dB / 5W
33 kOhm
5 RCA
2 XLR
<0,0009% / 1kHz , 5W
90dB
>100dB
230V / 50Hz / 420VA
435 x 170 x 485 mm
28 kg