AMPHORA Ready with Wheels Montage-instructies - Pagina 2

Blader online of download pdf Montage-instructies voor {categorie_naam} AMPHORA Ready with Wheels. AMPHORA Ready with Wheels 4 pagina's.

Pagina afdrukken

11)

Place the front arch on the front plate of the bottom.

Then bolt the smoke guard to the arch. Do not

tighten the joints too firmly, otherwise the damage of the

refractory shapes may occur due to heat dilatation.

Place the rear arch on the rear plate of the bottom.

16)

)

Place the front

Place the front parts T9 and T10 of the body to the stand above the

front arch (

front arch (push the front edge of the body to the portal as much

as poss

as possible). Before you connect the two parts, apply

adequate amount of silicone caulk into the locks and on

adeq

silicone caulk. Use layers of the rubber pads P12 or P13

silico

to fill the gap between the glazed body and the outer stoppers

to fill the g

and glue them using the silicone caulk. Cut the rubber according to

and glue them

A purpose of the silicone caulk application between the two front parts is to connect them so

that they don't spread and also as a partial protection against water and humidity, if you don't

follow the warranty conditions to place the oven under a roof or cover sheet.

19)

propertie

properties (elasticity, adhesion), and thus we suggest that the silicon

12)

Place the small side arch between the front

and rear arch. Side arches should be placed with

a hole towards the front portal.

the whole surface between the parts. Make sure the

caulk don't fill a hole for the thermometer. Maintain

a dilatational interstice at least 3 mm between

the upper edge of the front arch and the

front part of the body. For this purpose

place the supplied dilatation pads under the

side edges. If you use more than 2 pieces of

pads on top of each other, bind them together using

the size of the stoppers.

Apply silicone caulk between the body parts and along oven

Apply

circ

circumference between the bottom edge of the body and the

stand - into the formed joint, the used dilatation pads should

also get fixed. Silicone the chinks in the way the silicone

disassembling the oven (e.g. in the case of a warran-

ty claim). A purpose of this silicone caulk application

is to prevent water and humidity to get into the oven

so it is strongly recommended to use it even in the

case, you would have your oven under the roof. If you

don't have oven under the roof, using silicone does not

prevent on 100% the ingress of water into the oven so always

pre

use a cover sheet. Silicon caulk may after some time lose its

use a

caulk should be applicated again on the oven after this time.

13)

Place the central part of the arch with a hole

towards the chimney. Shape should be placed

on the top of the arch.

17)

Place the rear body to the

stand above the rear arch.

20)

14)

15)

Place the last two shaped pieces

into the remaining space so that the locks match.

18)

as possible. If it is necessary to align the parts, place

the supplied dilatation pads under the side edges, prefera-

bly at places marked by arrows (9 points). Do not remove the pads. If you use more than 2

pieces of pads on top of each other, bind them together using silicone caulk. Use layers of the

rubber pads P12 or P13 to fill the gap between the glazed body and the outer stoppers and

glue them using the silicone caulk. Cut the rubber according to the size of the stoppers.

Cut out a ho

Cut out a hole for the chimney (through insulation and the aluminium foil). Place the rope

seal into the opening in the front body into the prepared groove in the inner front arch

seal into

to cre

to create two threads of rope seal. Insert carefully the chimney base until the cover

flan

flange sits properly on the oven body. You can check with your hand from inside

of the chimney if the rope doesn't get distorted while inserting the chimney

base (if the rope gets damaged, heat and smoke can get into the space

between the inner shapes and the body). Turn the dumper always

lightly, not more than 90 degrees. Otherwise the thread may turn

and the sign "open, closed" may not correspond with an actual position.

Preferably don't pull out the chimney base out of the oven very often other-

wis

wise the rope seal may get damaged. When attaching chimney which is longer

than hal

than half a meter, make sure that chimney system is not exerting excessive pressure

on the body. C

on the body. Close the oven with steel door. Last, place the thermometer into the opening

behind the c

behind the chimney (for proper mounting it is necessary to pierce through the insulation).

Cover the assembled arch with at least 1 layer of

aluminium foil I8. Place the isolation bio-mat on the

aluminium foil according to the cutting plan for the

bio-mat. Make sure the bio-mat doesn't get distorted

during the application.

Place the central part of the body on

the stand between individual parts of

the body so that the cutouts of individual

shaped pieces match and joints are as narrow